7
PT
| Manual de instruções
1)
Com uma compreensão básica do
recuo poderá reduzir ou eliminar o
elemento de surpresa. Surpresas sú-
bitas contribuem para os acidentes.
2)
Segure bem a serra com as duas
mãos, a mão direita no punho traseiro
e a mão esquerda no punho da frente,
quando o motor estiver a funcionar.
Segure firmemente com os dedos e
os polegares envolvendo os punhos
da motoserra. Uma prisão firme aju
-
dará a reduzir o recuo e a manter o
controlo da serra.
3) Assegure-se de que mantém a área
onde está a executar o corte livre de
obstáculos. Não deixe a ponta da guia
entrar em contacto com um tronco,
ramo ou qualquer outro obstáculo que
possa ser atingido ao operar a serra.
4)
Corte a alta velocidade do motor.
5)
Não se estique nem corte acima da
altura do ombro.
6)
Siga as instruções do fabricante em
relação à manutenção da corrente
da serra.
7)
Use apenas guias e correntes sobres-
salentes especificadas pelo fabricante
ou equivalentes.
5. Instalação da guia e da corrente da serra
Um pacote de unidade de serra padrão contém os ele
-
mentos ilustrados:
1)
Unidade motriz
2)
Corrente da serra
3)
Guia
4)
Protector da guia
5)
Chave de velas
6)
Lima
Abra a caixa e instale a guia e a corrente da serra na
unidade motriz como se segue.
ATENÇÃO
A corrente da serra tem bordos muito afiados. Use luvas
de protecção grossas para segurança.
1.
Puxe a guarda na direcção do punho da frente para
verificar que o travão de corrente não está activado.
2. Desaperte as porcas e remova a guarda corrente.
3. Engate a corrente no pinhão e, instalando a corrente
da serra à volta da guia, monte a guia na unidade
motriz.
1) Porca tensora da corrente
2) Tampa da embreagem
3) Porcas
NOTA
Preste atenção ao sentido correcto da corrente da serra.
1) Sentido de movimento
4.
Ajuste a guarda corrente na unidade motriz e aperte
as porcas com os dedos.
5. Coloque a porca tensor de corrente no orifício
inferior da barra de guia, em seguida, instalar a
cobertura corrente, e aperte a porca de fixação com
os dedos.
6.
Segurando na ponta da guia, ajuste a tensão da
corrente rodando o parafuso tensor até que os elos
de ligação apenas toquem na parte inferior da calha
da guia.
7.
Aperte firmemente as porcas com a ponta da guia
levantada (12 a 15 N•m). Depois verifique se a cor
-
rente roda suavemente e se tem a tensão correcta
deslocando-a à mão. Se necessário, reajuste com a
guarda corrente solta.
8. Aperte o parafuso tensor.
Summary of Contents for PC 41 TL
