16
1.
Use a soft, dry cloth to wipe the area between the belt and deck.
2.
Spread lubricant onto the inside surface of belt and deck evenly (make sure the machine is turned off and power
is disconnected).
3.
Periodically lubricate the front and rear rollers to keep them at there peak performance.
If the treadmill belt/deck/roller is kept reasonably clean it is possible to expect over 1200 hours before additional
re-lubricating is necessary.
6
666.4.
.4.
.4.
.4. How
How
How
How to
to
to
to check
check
check
check the
the
the
the running
running
running
running mat
mat
mat
mat for
for
for
for proper
proper
proper
proper lubrication
lubrication
lubrication
lubrication
1.
Disconnect the main power supply.
2.
Fold the treadmill up into the storage position.
3.
Feel the back surface of the running mat.
If the surface is slick when touched, then no further lubrication is needed.
If the surface is dry to the touch, apply a suitable silicone lubricant.
We
We
We
We recommend
recommend
recommend
recommend you
you
you
you use
use
use
use aaaa silicone
silicone
silicone
silicone based
based
based
based spray
spray
spray
spray to
to
to
to lubricate
lubricate
lubricate
lubricate your
your
your
your Treadmill.
Treadmill.
Treadmill.
Treadmill. This
This
This
This Can
Can
Can
Can be
be
be
be purchased
purchased
purchased
purchased from
from
from
from your
your
your
your local
local
local
local
sports
sports
sports
sports Retailer
Retailer
Retailer
Retailer or
or
or
or aaaa local
local
local
local hardware
hardware
hardware
hardware store.
store.
store.
store.
6.5.
6.5.
6.5.
6.5. Belt
Belt
Belt
Belt Adjustment
Adjustment
Adjustment
Adjustment
Belt Tension Adjustment-It is very important for joggers and runners in order to provide a smooth, steady running
surface. Adjustment must be made from the right and left rear roller in order to adjust tension with the Hexagonal
Wrench provided in the parts package. The adjustment bolt is located at the end of the rails as noted in diagram
below:
Note:
Note:
Note:
Note: Adjustment
Adjustment
Adjustment
Adjustment is
is
is
is thru
thru
thru
thru the
the
the
the small
small
small
small hold
hold
hold
hold on
on
on
on the
the
the
the end
end
end
end caps.
caps.
caps.
caps.
Tighten the rear roller only enough to prevent slippage at the front roller. Turn both the right and left bolt clockwise
reasonably and inspect for proper tension. When an adjustment is made to the belt tension, you must also make a
tracking adjustment to compensate for the change in belt tension.
DO NOT OVERTIGHTEN - Over tightening will cause belt damage and premature bearing failure
....
6
666.6.
.6.
.6.
.6. Belt
Belt
Belt
Belt Tracking
Tracking
Tracking
Tracking Adjustment
Adjustment
Adjustment
Adjustment
This treadmill is designed to keep the belt reasonably centred while in use. It is normal for some belts to drift near
one side while the belt is running with no one on it. After a few minutes of use, the belt should have a tendency
Left bolt
Right bolt
Summary of Contents for Homeform20
