• Consult a specialist if you have any doubts regarding the use or safety of the
product.
• Maintenance, modifications and repairs must be carried out by a technician or a
specialist repair centre.
• If you are not sure about how to connect or operate the device, or if questions arise
which are not covered by the operating instructions, contact our technical support
or another specialist.
• In addition, observe the additional safety information in each section of these in-
structions.
• Also observe the safety and operating instructions of any other devices that are
connected to the work lamp.
b)
Rechargeable battery
• The in-built battery cannot be removed and can only be charged in the device.
Never attempt to remove the battery and charge it with an external charger.
• The rechargeable battery may only be charged via the USB connection of a USB
power supply with a suitable load capacity (see "Technical Data” section). Using
another power supply with a different charging current may damage the device
and cause the built-in battery to overheat, catch fire or explode.
c) Operation
• Warning, LED light
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
• Make sure the specifications of any devices which are charged using the charging
function conform to the product specifications listed in the “Technical data“ section.
Charging the battery
The work lamp battery must be charged via a USB power supply that provides an
output voltage of 5 V DC and has a current rating of at least 1 A. If the USB power
supply does not meet these requirements, the power supply or the work lamp may
be damaged.
USB ports on computers are often not powerful enough to charge this device.
Overloading may damage the USB interface or the computer.
Fully charge the battery before using the device for the first time. The charging time
is approx. 5-7 hours.
Charge the battery on a regular basis, even when you are not using the device (at
least once every two months). Failure to charge the battery regularly may cause the
battery to overdischarge, which can cause permanent damage.
• Open the red cover on the back of the device and connect the enclosed USB-C cable to the
USB-C port (small connection socket).
• Connect the other side of the USB-C cable to the USB port on your USB power supply.
• If necessary, turn on the USB power supply.
• The work lamp's built-in rechargeable battery will start to charge.
• During the charging process, the capacity indicator below the function key will turn on or
flash.
• The more bars displayed, the more the battery is charged. When the charging process is
complete, all the segments on the battery charge indicator will light up.
• If the work lamp no longer switches on or the last segment on the capacity indicator is
flashing, this indicates that the battery is discharged and must be recharged as described.
Depending on the selected light function or brightness, a full charge will power the
lamp for approximately 2.5-8 hours (refer to the "Technical Data” section).
When charging is complete, close the red cover on the back of the device to ensure
that the device is protected against penetrating objects and water spray.
Operation
a) Mounting
• The back of the housing features a fold-out hook, with which the work lamp can be suspended.
• Alternatively, you can fold out the stand on the bottom of the housing.
• The stand features two built-in magnets, which allow you to attach the lamp to magnetic
surfaces.
Operating instructions
Work lamp, 10W COB 1000L
Item No. 2443658
Intended use
This product is intended to be used as a work light. It has three light functions, as well as a
USB-A-output for charging/operating devices via USB (power bank function).
The work lamp features an IP44 protection rating, meaning it is protected against penetration of
objects greater than or equal to 1 mm, and against water spray from all directions.
The device is powered via a built-in rechargeable battery and must only be charged via a USB
power supply. This USB power supply must be able to deliver the current listed in the "Techni-
cal Data” section.
Any use other than that described above may damage the product and will expose you to ad-
ditional risks such as eye damage, short circuits, fire, electrical shocks etc.
This product complies with statutory, national and European regulations. All company and prod-
uct names contained herein are trademarks of their respective owners. All rights reserved.
Delivery content
• Work lamp
• USB-C cable
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Description of symbols
The symbol with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and tips on how to use the product.
Safety information
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety information and information on proper handling in these
operating instructions, we will assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
a) General information
• This product is not a toy. Keep it out of the reach of children and pets.
• The product is only designed for household use, and not for commercial or in-
dustrial use.
• For safety reasons, any unauthorised conversion and/or modification of the prod-
uct is not permitted.
• Do not leave packaging material lying around carelessly. It may become a danger-
ous plaything for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, flam-
mable gases, vapours and solvents.
• Handle the product carefully. Jolts, impacts or a fall even from a low height may
damage the product.
• Never expose the product to any excessive mechanical stress.
• If it is no longer possible to operate the product safely, stop using it and prevent
unauthorised use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stress.
• Discontinue use of the appliance in the event of malfunctions, defects or after a
fall and have it repaired by a specialist. Improper repairs may result in substantial
hazards to the user of the appliance.
