background image

Customer Helpline

 1300 889 028

3

Safety Information 

Important 

- Please read these instructions fully before starting assembly

Warning Symbols

To reduce the risk of injury, Please read the instruction manual

Warning

Wear ear protection  

 

Wear eye protection

Wear dust mask 

 

 

Indoor use only

Batteries may enter water cycle if disposed improperly, which can be hazardous for 
ecosystem. Do not dispose of waste batteries as unsorted municipal waste.    

Do not burn

Waste electrical products must not be disposed of with household waste. Please recycle 
where facilities exist. Check with your local authorities or retailer for recycling advice.

Li-ion battery. This product has been marked with a symbol relating to ‘separate 
collection’ for all battery packs and battery pack. It will then be recycled or 
dismantled in order to reduce the impact on the environment. Battery packs can be 
hazardous for the environment and for human health since they contain hazardous 
substances.

Fuse

Positive terminal

Negative terminal

RCM marking

Read the operator’s manual

ABN: 

Australian Business Number. By this number, business information such as entity 

type, status, business location etc. can be found at website http://abr.business.gov.au. 
ABN of Positec Australia Pty Limited is 14 101 682 357

Li-Ion

Li-Ion

Summary of Contents for CPS18LD.9

















Reviews: