Toolson 3901208958 Instruction Manual Download

Page: 15 / 180

15 І 180

any kind release the main switch button located on the
handgrip, thus disconnecting the machine.

• Always keep hands away from the work area when

the machine is running; before performing tasks of

any kind release the main switch button located on the
handgrip, thus disconnecting the machine.

Assembly

WARNING! For your own safety, never connect the

plug to power source outlet until all assembly steps
are completed and you have read and understood

the safety and operational instructions.

Lift the saw from the packaging and place it on your work
bench.

Installing the Dust Bag (Fig. 2)

• Squeeze the metal collar wings 2 of the dust bag and

put it on the motor area exhaust port 1.

Setting the Tool

Note:

This tool is accurately adjusted before shipping from the
factory. Check the following accuracy and readjust if nec-
essary in order to obtain the best results in operation.

Installation of the Angle Fence at 90°, Fig. 3

Loosen the angle clamping lever (1).

Move the cutting head to the right until it rests against

the fence.

Tighten the angle clamping lever (1).

Test the saw blade with a 90° angle to the saw table.

If an adjustment is necessary, loosen the lock nut (2)
and position the socket screw in such a way that the saw
blade stands at 90° to the table. Re-tighten the lock nut.

Set the angle fence (3) with the screw at 0.

Installation of the Angle Fence at 45° Left. Fig.4

Loosen the angle clamping lever (1).

Move the cutting head to the left until it rests against

the fence.

Tighten the angle clamping lever (1).

Test the saw blade with a 45° angle to the saw table.

If an adjustment is necessary, loosen the lock nut and
position the socket screw (4) in such a way that the saw
blade stands at 90° to the table. Re-tighten the lock nut.

Installation of the Contact Surface,

• Lower the cutting head and push in the lock pin. Make

sure the table is in 0 mitre position.

• Place a combination square against the fence and

next to the saw blade.

• Loosen the two screws if the saw blade does not

touch the protractor.

• Adjust the fence so that the fence has full contact with

the square. Tighten the screws.

Connecting to the Power Supply

Check that the power supply and outlet used are in ac-

cordance with your mitre saw. Have a look at the rating

plate of the motor or the rating on the mitre saw. Any

changes should always be carried out by a qualified

electrician.

Any functional dis orders, especially those affecting the

safety of the machine, sholud terefore be rectified im

mediately.

•

Any other use exceeds authorization. The manufac

turer is not responsible for any damages resulting from

un authorized use; risk is the sole responsibility of the

operator.

• The safety, work and maintenance instructions of the

manufacturer as well as the technical data given in

the calibrations and dimensions must be adhered to.

•

Relevant accident prevention regulations and other,

gene rally recognized safety-technical rules must also
be adhered to.

• The machine may only be used, maintained, and op-

erated by persons familiar with it and instructed in its
operation and procedures. Arbitrary alterations to the
machine release the manufacturer from all responsi-
bility for any resulting damages.

• The machine may only be used with original accesso-

ries and tools made by the manufacturer.

Remaining hazards

The machine has been built using modern technolo-

gy in accor dance with recognized safety rules. Some

remaining hazards, how ever, may still exist.

• Only process selected woods without defects such

as: Branch knots, edge cracks, surface cracks. Wood
with such defects is prone to splintering and can be
hazardous.

•

Wood which is not correctly glued can explode when

being processed due to centrifugal force.

• Trim work piece to a rectangular shape, center and