Toolson 3901403958 Instruction Manual Download

Page: 19 / 240

12 Do not overstretch

Avoid abnormal working postures. Make sure
you stand squarely and keep your balance at all
times.

13 Take care of your tools

Keep your tools sharp and clean in order to work
well and safely. Follow the maintenance infor-
mation and the instructions for changing tools.
Check the power plug and cable on a regular
basis and have them replaced by an authorized
specialist if they are damaged. Check theexten-
sion cable regularly and replace it if damaged.
Keep handles dry and free from oil and grease.

14 Pull out the power plug

When tools are not in use, before starting any
maintenance work or when changing attach-
ments such as saw blades, drill bits and all kinds
of mounted tools.

15 Always remove keys and wrenches after use

Always check that keys, wrenches and other
adjusting tools have been removed before you
switch on the equipment.

16 Avoid unintentional starting

Never carry a tool with your finger on the switch

button while the tool is connected to the power
supply. Make sure that the switch is turned off
when connecting the tool to the power supply.

17 When using an extension cable outdoors

Check that it is approved for outdoor duty and is
marked accordingly.

18 Be alert at all times

Watch what you are doing. Use common sense
when working. Never use the tool when you are
distracted.

19 Check your tool for damage

Before using the tool again, check the safety
devices or any slightly damaged parts to en-
sure that they are in good working order. Check
that the moving parts are working correctly, that
they do not jam, and that no parts are damaged.

Make sure that all parts are fitted correctly to

ensure that the equipment remains safe to use.
Unless otherwise stated in the operating instruc-
tions, damaged guards and parts have to be re-
paired or replaced by a customer service work-
shop. Damaged switches have to be replaced
by a customer service workshop. Never use an
electric power tool with a switch that cannot be
turned on and off.

20 Important.

For your own safety you must only use the ac-
cessories and additional units listed in the oper-

ating instructions or recommended or specified

by the manufacturer. The use of mounted tools
or accessories other than those recommended
in the operating instructions or catalog may
place your personal safety at risk.

Repairs may only be carried out by a qualified

electrician

This electric power tool complies with the perti-
nent safety information. Repair work must only
be carried out by a trained electrician, otherwise
the equipment may cause accidents.

22 Connect up the dust extraction system

If there are provisions for connecting up a dust
extraction system, make sure that such a system

is fitted and in use.

Additional safety instructions

• Switch the machine off immediately and pull the

power plug in an emergency.

• Follow all these safety instructions before and while

working with the saw.

•

Do not use this saw to cut fire wood.

• Do not use this saw to cross-cut roundwood with-

out a suitable holding device.

• The machine is equipped with a safety switch to

prevent it from being switched on again acciden-
tally after a power failure.

• If you need to use an extension cable, make sure

its conductor cross-section is big enough for the
saw’s power consumption. Minimum cross-section
1 mm

• If you use a cable reel, the complete cable must be

pulled off the reel.

• Persons working on the machine should not be dis-

tracted.

• After you have switched off the motor, never slow

down the saw blade by applying pressure to its
side.

•

Only fit blades which are well sharpened and have

no cracks or deformations.

• Faulty saw blades must be replaced immediately.
• Never use saw blades which do not comply with the

data specified in this manual.

• It is imperative to make sure that all devices which

cover the saw blade are in good working order.

• Never dismantle the machine’s safety devices or

render them inoperative.

• Damaged or faulty safety devices have to be re-

placed immediately. Never cut workpieces which
are too small to hold securely in your hand.

• Never load the machine so much that it cuts out.
•

Always press the workpiece firmly against the saw

table.

• Never remove loose splinters, chips or jammed

pieces of wood when the saw blade is running.

• Switch the machine off to rectify faults at the

blocked plug-in tool. - Pull the power plug- Remove
the blockage. Important! Risk of injury from saw
blade! Wear gloves. Carry out a trial run without a
workpiece. Ensure that no unusual noise or vibra-
tion occurs. Should this be the case, switch the unit
off and contact the manufacturer.

• Carry out retooling work, adjustments, measure-

ments and cleaning jobs only when the motor is
switched off. - Pull the power plug. -