Tilt detection function
(
During communication with LS-B110W only)
Switching the tilt direction
The tilt direction can be changed.
1
Long-push the detective precision switch and the tilt switch at
the same time. The tilt direction mode setting changes in the
following order: "Back and Forth," "OFF" and "Right and Left."
At this time, the LED above the mark indicating the tilt direction
will flash. The LED will not flash when the tilt detection function
is switched OFF.
Switching the tilt precision
1
Short-push the tilt switch. The tilt precision will change. At
this time, the LED below the mark indicating the tilt precision
will light up.
Zero position setting for the tilt sensor
Before using the tilt detection function, set the zero position of the tilt
sensor according to the directions below. The tilt direction must be set
before setting the zero position.
1
Raise or lower the machine blade or arm where the LS-B110W
is installed to position the cutting edge or bucket at the desired
slope.
2
Long-push the tilt switch on RD-100W. The tilt angle for the
LS-B110W will set to 0
°
.
Tilt angles and display patterns
Tilt directions : Right and Left
Tilt directions : Back and Forth
Tilt indication will be displayed during laser detection and for 20 seconds after switch
operation.
Changing the ON-GRADE position function
(During communication with LS-B110W only)
The ON-GRADE position can be changed to the position where laser
beam is detected. Using this function when installing the LS-B110W
on the pole of the machine allows easy setting of the height at which
the ON-GRADE will be displayed on the LS-B110W. The range in
which the ON-GRADE position can be changed is ±75mm (total of
150mm) from the center of the detective range.
In order to set the ON-GRADE position at high precision, set it while
the laser beam is stable. When setting the ON-GRADE position while
the laser beam is unstable (when using at a long-distance - more than
150m - or when atmospheric condition is unstable due to air shimmer-
ing or other conditions), the sensor will automatically detect it and the
LED indicating the failure will be displayed while changing the ON-
GRADE position.
1
Long-push the zero-set switch while detecting the laser beam.
The LED display and LCD display while changing the ON-
GRADE position
Cancellation the ON-GRADE position change
1
Long-push the zero-set switch when not detecting the laser
beam. The ON-GRADE position will be reset.
High precision
Normal precision
: ±1°
: ±2.5°
Flashes quickly
±5°
More than ±5°
Flashes slowly
Lights off
: More than ±1°
: More than ±2.5°
High precision
Normal precision
High precision
Normal precision
: ±1°
: ±2.5°
Flashes
7400 National Drive, Livermore, CA 94551, U.S.A.
Phone: 925-245-8300 Fax: 925-245-8599 www.Topconpositioning.com
3380 Industrial Blvd, Suite 105, West Sacramento, CA 95691, U.S.A.
Phone: 916-374-8575 Fax: 916-374-8329
Essebaan 11, 2908 LJ Capelle a/d IJssel, The Netherlands.
Phone: 010-458-5077 Fax: 010-284-4941 www.topconeurope.com
Giesserallee 31, 47877 Willich, GERMANY
Phone: 02154-885-100 Fax: 02154-885-111 info@topcon.de
www.topcon.de
89, Rue de Paris, 92585 Clichy, Cedex, France.
Phone: 33-1-41069490 Fax: 33-1-47390251 topcon@topcon.fr
Phone: 031-7109200 Fax: 031-7109249
Topcon House Kennet Side, Bone Lane, Newbury, Berkshire RG14 5PX U.K.
Phone: 44-1635-551120 Fax: 44-1635-551170
survey.sales@topcon.co.uk laser.sales@topcon.co.uk
Blk 192 Pandan Loop, #07-01 Pantech Industrial Complex, Singapore 128381
Phone: 65-6778-3456 Fax: 65-6773-6550 www.topcon.com.sg
77/162 Sinn Sathorn Tower, 37th Fl.,
Krungdhonburi Rd., Klongtonsai, Klongsarn, Bangkok 10600 Thailand.
Phone: 66-2-4401152~7 Fax: 66-2-4401158
No.D1, (Ground, Lower Ground & 1st Floor), Jalan Excella 2, Off Jalan Ampang
Putra, Taman Ampang Hilir, 55100 Kuala Lumpur, Malaysia
Phone: 60-3-42709866 Fax: 60-3-42709766
Block No.9, Kangding Street
Beijing Economic-Technological Development Area, Beijing, 100176, China
Phone: 86-10-6780-2799 Fax: 86-10-6780-2790
P. O Box293705, Office C-25(row C-2), Dubai Airport Free Zone, Dubai, UAE
Phone: 971-4-2995900 Fax: 971-4-2995901 marketing@Topcon.ae
Unit 69 Western Parkway Business Center
Phone: 01460-0021 Fax: 01460-0129
Lower Ballymount Road, Dublin 12, Lreland
7G
When changing the ON-GRADE position, the LED lights up
for three seconds, as shown in the figure. The position where
the laser beam is being detected will be the ON-GRADE
position.
The LED display indicating beam position and the
LED (1 green) in the center will flash. The mark
showing laser beam position on the LCD will flash.
When the ON-GRADE position change is cancelled,
the LED (3 green) will flash for three seconds.
Specifications
Wireless communication
range
:
20m
(May vary depending on obstacles between
the two instruments and other conditions)
Power source
:
AA-size dry cells 3pcs.
Continuous operating time
(+20
°
C/+68
°
F)
:
Approximately 40 hours
(Using alkaline manganese dry cells)
Operating temperature
:
-20
°
C~+50
°
C(-4
°
F~+122
°
F)
Water proof
:
IP66 (Based on the standard IEC60529)
Dimensions (W/D/H)
:
110x36x176(mm) (4.3
″
x1.4
″
x6.9
″
)
Weight (Without cells)
:
0.5kg (1.2lbs)
Detective angle, Detective precision and Laser detecting range may vary
depending on rotating laser being used or atmospheric conditions.
Tilt direction mark :
Right and Left
Tilt direction mark :
Back and Forth
Tilt precision mark :
High precision
Tilt precision mark :
Normal precision
The LED (1 green) lights up as shown in the figure
for three seconds when the zero position is set.
The LED (2 red) flashes as shown in the figure for
three seconds when you have failed to set the
zero position.
The LED lights up as shown in the figure for three seconds
when you have failed to change the ON-GRADE position. Be
careful not to change the position at which the laser beam is
detected and try setting once again.
31267 90113
