background image

11 

sunlight. 

 

Step 3   

Insert the cable of the second gate opener and Warning Light cables into the control box through middle strain 

relief. Then repeat step 2. 

Step 4 

Insert the cables of the optional parts into the control box through the right strain relief. Then repeat step 2. 

 

 

Connection of Power Supply 

      

WARNING: NEVER connect the gate opener to the power supply before all the installations have 

been done.   

Connect the power supply to the Control Box refers to 

the following illustration. 

NOTE:   

1. Use copper conductors to connect to the power 

supply terminals.   

2. The wire (not provided) size should be at least 

0.75mm

(18AWG)  which is intended to connect the 

power supply. 

3. Run the wires in conduit to the control box to 

prevent damage to the wires from lawn mowers, weed 

eaters and grazing animals. 

4. The fuse in the control board is interchangeable. A 

10a, 250vac, Φ5*20mm fus

e is suitable to the control 

board. 

 

 

Connecting of the Control Board 

Motor connection for PULL-TO-OPEN 
Motor 1 

Insert the stripped cable wires into the appropriate terminals on the opener terminals block. The red wire should 

be inserted into the “

” 

terminal, the black wire into “

MOTOR1-“

, the blue wire into 

ULT1

, the green 

wire into 

COM

, and the thin yellow wire into 

DLT1

 terminal. 

Motor 2 

Similar as the connection of 

Actuator 1

, insert the stripped cable wires into the appropriate terminals on the 

opener  terminals block.  The red wire should be inserted into the “

” 

terminal, the black wire into 

MOTOR2-“

, the blue wire into 

ULT2

, the green wire into 

COM

, and the yellow wire into 

DLT2

 terminal. 

NOTE:

 It is recommended that Gate Opener 1 is installed in the Master Gate, and Gate Opener 2 is installed in 

the Slave Gate. 

Summary of Contents for KD702




























Reviews: