GTalarm3 User manual V-2022-05-24
54 |
E N
4
SIM ICCID
ICCID (Integrated Circuit Card Identifier)
- A SIM card contains its unique serial number (ICCID).
ICCIDs are stored in the SIM cards and are also printed on the SIM card.
5
SIM Card
If note READY is visible, it means that SIM card is fully functioning. Otherwise, check whether PIN
code request is off or replace SIM card.
6
Signal level
Signal strength of GSM communication
7
Registration
State of GSM modem registration to GSM network.
8
SMS Service Centre
Address
SMS center number. This number should be checked if it is correct. If this number is incorrect. SMS
messaging may be impossible. This number may be changed after inserting SIM card into any mobile
phone.
9
System Voltage
Power supply voltage. Nearby number is value of ADC voltage. When multiplying this number by the
coefficient Fig. 32, voltage value (V) will be achieved.
10
System Voltage
System voltage OK/Trouble
11
RTC Clock
Real time clock OK/Trouble
12
Module Real Time Clock
Indicates the time of the module RTC
13
Set RTC Clock
By pressing this button real time clock of the module will be set.
14-17
Inputs In1…In4
In1…In4 is the indicated input ADC and voltage value V.
18-19
I/O1…I/O2
I/O1…I/O2 is the indicated voltage ADC value and current ADC value mA.
20-22
D1…D3 (I/O)
Check box nearby the digital inputs D1…D3 (I/O) means that the input has ‘0’ or ‘1’ state.
23
BUS (I/O)
Check box nearby the zone expansion module BUS (I/O) means that the input has ‘0’ or ‘1’ state.
24-27
Out1…Out4 On/Off
Checked box nearby the appropriate output
Out1…Out4
means that this output currently has ‘0’ or ‘1’
state. The output could be activated by pressing On/Off button
28-29
I/O1…I/O2 On/Off
Checked box nearby the appropriate input/output
I/O1…I/O2
means that this input/output currently has
‘0’ or ‘1’ state. The output could be activated by pressing On/Off button
30-32
D1…D3 (I/O) On/Off
Checked check box nearby the digital outputs
D1…D3 (I/O)
means that the output currently has ‘0’ or
‘1’ state.
33
BUS (I/O) On/Off
Checked check box
BUS (I/O)
means that the output currently has ‘0’ or ‘1’ state.
4.12 RT Testing & Monitoring Security Alarm Panel/ Access
RT Testing & Monitoring > Security Alarm Panel/ Access
The Security Alarm Panel/ Access window let you see real time zones states: is zone
alarmed, bypassed, forced etc. This window it let you change system state: disarm, arm,
sleep, and stay. This window let you look to access control area also.
2
3
4
5
6
7
8
13
14
15
16
9
10
11
12
17
18
19
1
Figure 51 the example of RT Testing & Monitoring > Security Alarm Panel/ Access window
If the checkbox is checked and the color is red the trouble is indicating. If color is green, trouble is not indicated. The text nearby indicates the trouble.
Table 10 Explanation of every field in "Security Alarm Panel/ Access" window
1
Zone1…Zone32
Zone number
2
Alarm
If checked and the color is red the zone is alarmed
4
Alarm Shutdown
If checked and the color is red alarm shutdown for the zone is activated. Allowable number of the
same alarm events is reached and the same events will not be reported.
6
Bypassed
If checked and the color is red, the zone is bypassed.
7
Forced
If checked and the color is red, the zone is forced
3
Tamper/Fault
If checked and the color is red, the zone is tampered.