TOPMAQ FTC200 Operating User Manual Download

Page: 2 / 15

- 2 -

CONTENTS

PAGE

I. SPECIFICATION----------------------------------------------------------------------------3

II.OPERATOR’S INSTRUCTIONS--------------------------------------------------------4

RANGE OF APPLICATIONS AND PROPER USE----------------------------------------------4

KNOW YOUR PRODUCT-----------------------------------------------------------------------------4

GENERAL SAFETY RULES --------------------------------------------------------------------------4

TRANSPORTATION-------------------------------------------------------------------------------------7

III.SPECIFIC SAFETY RULES--------------------------------------------------------------7

IV. SPECIAL SAFETY INSTRUCTIONS--------------------------------------------------8

V. INSTALLATION AND OPERATING-----------------------------------------------------9

A. STARTING AND STOPPING THE SAW------------------------------------------------------- 9

B. ASSEMBLY-------------------------------------------------------------------------------------------- 9

C. FILLING THE WATER TRAY AND DRAINING-----------------------------------------------10

D. MAKING A STRAIGHT CUT-----------------------------------------------------------------------11

E. MAKING

MITRE

CUT-----------------------------------------------------------------------------11

F. MAKING A BEVEL CUT-----------------------------------------------------------------------------11

G. MOVING THE SAW----------------------------------------------------------------------------------11
H. REPLACING THE DIAMOND BLADE-----------------------------------------------------------12

VI.MAINTENANCE-----------------------------------------------------------------------------12

VII.TROUBLE SHOOTING-------------------------------------------------------------------14

VIII. ACCESSORIES -------------------------------------------------------------------------14

IX. SERVICE--------------------------------------------------------------------------------------15

Summary of Contents for FTC200
















Search results

Summary of Contents for FTC200

Reviews:

Related manuals for FTC200

Brands by name

Popular brands

TOPMAQ FTC200, Operating User Manual

Search results

Summary of Contents for FTC200

Reviews:

Related manuals for FTC200

Brands by name

Popular brands