background image

- 5 - 

DIRECTION OF BLADE:

 

Please make sure the diamond blade always towards the same 

direction as the arrow which is molded on the blade guard.   

 
GENERAL SAFETY RULES   
WARNING!

 When using electric tools basic safety precautions should always be followed to reduce the 

risk of fire, electric shock and personal injury including the following. 
Read all these instructions before attempting to operate this product and save these instructions. 
 
1 –Keep work area clear 

-

  Cluttered areas and benches invite injuries. 

2 – Consider work area environment 

-

  Do not expose tools to rain. 

-

  Do not use tools in damp or wet locations. 

-

  Keep work area well lit. 

-

  Do not use tools in the presence of flammable liquids or gases. 

3 – Guard against electric shock 

-

  Avoid body contact with earthed or grounded surfaces (e.g. pipes, radiators, ranges, 

refrigerators). 

4 – Keep other persons away 

-

  Do not let persons, especially children, not involved in the work touch the tool or the extension 

cord and keep them away from the work area. 

5  -Store idle tools 

-When not in use tools should be stored in a dry locked-up place, out of reach of children. 

6  – Do not force the tool 

-

  It will do the job better and safer at the rate for which it was intended. 

7  – Use the right tool 

-

  Do not force small tools to do the job of a heavy duty tool. 

-

 

Do not use tools for purposes not intended, for example do not use circular saws to cut tree limbs 
or legs. 

8 –Dress 

properly 

-

  Do not wear loose clothing or jewelers; they can be caught in moving parts. 

-

  Non-skid footwear is recommended when working operations create dust. 

-

  Wear protective hair covering to contain long hair. 

9  -Use protective equipment 

-

  Use safety glasses. 

-

  Use face or dust mask if working operations create dust. 

10  –Connect dust extraction equipment 

-

 

If the tool is provided for the connection of dust extraction and collecting equipment, ensure these 
are connected and properly used. 

11  – Do not abuse the cord 

-

  Never yank the cord to disconnect it from the socket. Keep the cord away from heat, oil and 

sharp edges. 

Summary of Contents for FTD-202A

















Reviews: