Both knobs are used to determine the master AUX SEND levels. The
adjustable range is from -
to +15 dB. When the external effect
unit connected to mixer has no input gain control, you can get a
f15 dB gain available from these AUX SEND outputs.
20- MASTER AUX SEND Controls
When pressing this switch, the OL LED will
illuminate and the SOLO signal will replace
other signals and reach to the CONTROL ROOM/
PHONES. Usually use the SOLO function to
preview each channel before they are get into
the mix. You can solo more than one channel
at a time. And the soloed channels are sent to
the CONTROL ROOM, PHONES, and LED display.
Engaging the SOLO switch, all CONTROL ROOM
SOURCE selections MAIN MIX, CD/TAPE, ALT3-4
(
) & SUB1-2 (
) will be
muted.
MX.22/2FX
MX.26/2FX
14- SOLO SWITCH & OL LED
Each channel provides two assignment switches:
1-2, and L-R. Pressing the 1-2 will assign the
channel signal to SUB1-2, you can depend on the PAN / BAL control to adjust the amount of
channel signal sent to the SUB1 versus SUB2, when turns the PAN/BAL to completely left, then
the signal can be only controlled by SUB1 and vice-versa. In the same way, pressing the L-R will
assign the channel signal to MAIN MIX L-R. This switch must be engaged in to get the channel's
signal through to main outs.
15- 1-2 &
Switches(
MX.26/2FX)
L-R
only for
This control will adjust the overall level of this channel and set the amount of signal sent to the
main output.
16- Fader
Through these switches, you can operate the SUB1-2 faders as
a master control for assigning the SUB 1-2 to MAIN MIX. Engage
the LEFT switch to send the corresponding sub signal to MAIN MIX L, and the RIGHT switch
for MAIN MIX R. When engaging the both switches, the signal will be sent to L/R of MAIN MIX.
17- SUB ASSIGN TO MAIN MIX Switches (
MX.26/2FX)
only for
CONTROL ELEMENTS
L
L
R
R
SUB ASSIGN
TO MAIN MIX
17
18
19
12-INPUT 2 2BUS MIXER WITH DIGITAL EFFECTS
MX 22/2FX
.
ALT 3
ALT 4
MAIN MIX
0
5
10
50
40
60
30
20
10
5
0
5
10
50
40
60
30
20
10
5
0
5
10
50
40
60
30
20
10
5
0
5
10
50
40
60
30
20
10
5
18
19
MX 26/2FX
.
16-INPUT 2/2BUS MIXER WITH DIGITAL EFFECTS
-60
-50
-40
-30
-20
-10
-5
0
5
10
-60
-50
-40
-30
-20
-10
-5
0
5
10
-60
-50
-40
-30
-20
-10
-5
0
5
10
-60
-50
-40
-30
-20
-10
-5
0
5
10
MAIN MIX
SUB 1
SUB 2
These faders are used to control the levels of signal that send
to the ALT3-4OUT / SUB1-2 OUT. The range goes from -
to
+10 dB. By pushing in the MUTE/ ALT3-4 switch(for MX.22/2FX)
& SUB 1-2 ASSIGN switch ( for MX.26/2FX ), the signals will
appear at the ALT3-4/SUB1-2 OUTS.
18- ALT3-4 Master Faders (MX.22/2FX) & SUB1-2 Master Faders (MX.26/2FX)
These two faders set the level of main mix signals sent to the Main
Outputs, Tape Outputs, CONTROL ROOM, PHONES, and LED display.
Note: When connecting a speaker to the speaker output jacks on
rear panel, please pay more attention to the level setting for avoiding
damaging the speaker. Generally, the faders will be positioned
between 0 dB (U) & +5 dB.
19- MAIN MIX Faders
11
12
13
14
16
MX.22/2FX
CH1
OL
SOLO
MUTE
PRE
0
5
10
50
40
60
30
20
10
5
ALT
CH1
11
12
13
14
15
16
MX.26/2FX
PRE
MUTE
-60
-50
-40
-30
-20
-10
-5
0
5
10
OL
1-2
L-R
SOLO
5
Summary of Contents for MX.22/2FX
Page 1: ...USER S MANUAL NF03522 1 0 ...
Page 2: ......
