Remaining battery life display
Fig 13
4.3 Operating frequency matches between the receiver and the transmitter
To make the operating frequency match between the transmitter and the receiver, there are two options.
Controlled from the receiver, TMW-9144R
1) Auto Scan
Turn on the receiver,
the MEM key
. You can see"SCAN"
press
for a few seconds to enter into the auto scan mode
flashes on the top left of the LCD, it means the auto scan function has been activated. under the auto scan mode,
the scan function automatically searches the receiver's entire frequency band from start to stop. During the search,
these presets of GROUP, CHANNEL and frequency keep flashing as they are scanned. As soon as he correct
frequency is reached, the scan will be stopped automatically, the value of frequency will be flashing channel preset,
press the MEM key, you can save the information.
Adjust from the transmitter,
1) Check the preset frequency (preset group, and preset channel) displayed
2) Switch on the transmitter.
3) Touch the CH/ON key slightly to select the parameters to be edited.
4) Use the Select key to set the proper channel / group.
on the receiver in MHz.
2) Manually Selecting Frequency
MODEL
Channel
Frequency band
Receiver type
Frequency response
Frequency stability
T.H.D.
Modulation mode
S/N Ratio
Dynamic
RF sensitivity
Audio output
Balance output
Power supply
TMW-9144R
Multi-channels, up to 144 frequency presets for each frequency bands
UHF 470-900 MHz Dependent on applicable country regulations
PLL UHF SYNTHESIZED
50 Hz-15KHz (
3dB)
0.005% (-10
-50
)
1KHZ
0.8%
FM (F3E)
90dB
100dB
-100 dBm/30dB SINAD
Unbalanced 6.3mm phone jack 550mV 20KHz deviation
1V , 20KHz deviation
DC 15V/ 500mA (AC 110V/230V 50/60Hz adaptor)
5. TECHNICAL SPECIFICATIONS
210(W)
55 (D)
44(H)mm; (8.2"
6.1"
1.7")
Approx. 0.95kg
Weight
Dimensions
12
Remark: some frequencies should be scanned manually by adjusting UP/DOWN Key, please refer to user's
manual of TMW-9144R for details!
Turn on the receiver. After touch the MENU key, the 'Group' indicated on the LCD display flashes, and use the
UP/DOWN key to select the right group, after it is done, press 'Mem' to store the settings. To edit the preset
channel or other parameters, please press again the MENU key, and so on.
Summary of Contents for TMW-9144P
