background image

www.smstork.com

29

10. PRODUCT SPARE PARTS

Electrical actuators’ spare parts are; 
• Gears
• Motor
•  Electronic Control Cards
  • On-Off Control Cards
  • Proportional Control Cards
•  Position Indicator
•  Potantiometer Unit

You must choose spare parts according to your actuator model. For supplying spare 
parts and detailed information please contact to SMS TORK. 

11. PRODUCT SHIPMENT

During transportation be careful about electrical actuator’s not falling down and not being 
subjected hard knocks. Don’t put any weight damaging the product on electrical actuator 
boxes. Electrical actuators must be carried on their carton boxes. 

12. WARRANTY CONDITIONS

1)

 The period of warranty shall start from the date of delivery of the product to the 

customer and shall cover a period of 2 years.

2)

 Every and all parts of the product are under SMS Sanayi Malzemeleri Üretim ve Satışı 

A.Ş. warranty coverage. (against any defect that may occur during production, assembly 
and/or defective parts)

3)

 In the case that the product fails within warranty period, the time spent on the repair 

work is added to the warranty period. Repair time of the product is maximum 20 (twenty) 
working days. This time starts from the date on which the failure concerning the product 
is notified to the service station and to seller of the product, dealer, agency, representative, 
importer or producer. It is possible to make the consumer failure notification by telephone, 
fax, e-mail, registered mail or similar. However, in case of disagreement, the obligation of 
proof belongs to the consumer.

4)

 Product replacement or refund is mandatory depending on the choice of the consumer 

in case one of the conditions below:
 a) If failure occurs in the product at least four times in one year or six times with the 
condition of being within the warranty period.
 b) If the maximum time for its repair is exceeded.

Summary of Contents for TREA 0060

































Reviews: