Tormatic POWERSLIDE, Instruction Manual

PowerSlide 6 

ENGLISH

3.1  INTENDED USE

PowerSlide series gear motors are designed to operate horizontal 

sliding gates for residential use (including in apartment complexes).
One gear motor must be installed for each sliding gate section.  The 

gate must be moved via a rack.
Installations of PowerSlide must be used for vehicular traffic.
To operate the gate manually, follow the instructions in § .

!

Any other use which is not expressly specified in these instructions is 

prohibited and could affect the integrity of the product and/or represent 

a source of danger.

3.2  LIMITATIONS OF USE

The gate must fall within the dimensional and weight limitations indi-

cated in the technical data section.Obey the limitations on frequency 

of use listed in the technical data section.
Using the product in any configuration other than that provided 

for is prohibited. It is prohibited to modify any product component.
The presence of weather conditions such as snow, ice and strong 

wind, even when occasional, could compromise correct automation, 

affect the integrity of the components and represent a potential 

source of danger.
If a pedestrian access gate is integrated in the sliding gate section, 

motorised movement must be disabled when the pedestrian gate 

is not closed.
PowerSlide is not designed as a security (break-in protection) system.
Implementing automation requires the installation of the necessary 

safety devices, identified by the installer through an appropriate risk 

assessment of the installation site.

3.3  PROHIBITED USES

2.3  UNPACKING AND HANDLING

RISKS

PERSONAL PROTECTIVE EQUIPMENT

1.  Open the package.

L

i

The gear motor casing is not fixed.

2.  Remove the magnetic limit switches and the bag of accessories.
3.  Remove the casing.

!

Do not lift the gear motor by the electronic board.

4.  Lift the gear motor, holding it by the base.

L

i

Check that all components are present and intact 

 2

.

5.  Dispose of the packaging materials.

3.  POWERSLIDE

!

The packaging materials (plastic, polystyrene etc.) must not be left 

within reach of children, as they are potential hazards.
When you have finished with them, dispose of the packaging in the 

appropriate containers, as per applicable waste disposal regulations.

2.4  DISPOSAL OF THE PRODUCT

After having dismantled the product, dispose of it in compliance with 

the current waste disposal regulations.

Components and structural materials, batteries and electronic compo-

nents must not be disposed of together with household waste. They 

must be taken to authorised disposal and recycling centres.
The oil must be gathered in a watertight container and given to 

an authorised disposal and recycling centre. Do not mix with other 

substances such as antifreeze or transmission fluids. Keep the used oil 

away from sources of heat and out of the children's reach. The fluid is 

not hazardous to health.  In case of contact with eyes, skin or clothing, 

wash and rinse the affected parts.
The technical data sheets of the fluids are available on request.

-

Uses other than the intended use are prohibited.

-

It is prohibited to install the automation system outside of the 

limits specified in the Technical Data and Installation Require-

ments sections.

-

It is forbidden to use PowerSlide in a constructional configuration 

other than the one provided by the manufacturer.

-

No component part of the product may be modified.

-

It is prohibited to install the automation system on escape routes.

-

It is prohibited to install the automation system to create fire 

doors.

-

It is prohibited to install the automation system in environments 

in which there is a risk of explosion and/or fire: the presence of 

flammable gases or fumes is a serious safety hazard.

-

It is prohibited to power the system with energy sources other 

than those specified.

-

It is prohibited to integrate commercial systems and/or 

equipment other than those specified, or use them for purposes 

not intended and authorised by their respective manufacturers.

-

Do not allow water jets of any type or size to come into direct 

contact with the gear motor.

-

Do not expose the gear motor to corrosive chemicals or atmo-

spheric agents.

-

It is prohibited to use and/or install accessories which have not 

been specifically approved.

-

It is prohibited to use the automation system before performing 

commissioning.

-

It is prohibited to use the automation system in the presence of 

faults which could compromise safety.

-

It is prohibited to use the automation system with the fixed and/

or mobile guards removed or altered.

-

Do not use the automation system unless the area of operation 

is free of persons, animals or objects.

-

Do not enter/remain in the area of operation of the automation 

system while it is moving.

-

Do not try to prevent the movement of the automation system.

-

Do not climb on, hold onto or let yourself be pulled by the 

leaf.  Do not climb onto the gear motor.

-

Do not allow children to approach or play in the area of operation 

of the automation system.

-

Do not allow the control devices to be used by anyone who is 

not specifically authorised and trained to do so.

-

Do not allow the control devices to be used by children or persons 

with mental and physical deficiencies unless they are supervised 

by an adult who is responsible for their safety.

!

During manual operation, gently guide the leaf the whole way, do not 

push it and let it slide freely.