Tormatic T100 R Assembly And Operating Instructions Manual Download

Page: 29 / 108

EN - 27

T100 R

Operation

Safety instructions for operation

Observe the following safety information for operation:

•

The operator must be instructed on how to handle the
control or the controlled door system and be familiar with the
applicable safety regulations.

•

Comply with the accident prevention regulations and
general safety regulations relevant to the field of application.

•

Check the control and the door system connected for visual
defects before use.

•

If you detect any safety-relevant deficiencies, decommission
the door system and report all defects to the responsible line
manager.

•

Have the deficiencies remedied immediately.

•

If the operational behaviour of the door system changes,
switch the system off immediately. Recommissioning must
be prevented. Notify the operating company of the change.

CAUTION

Crush hazard and risk of being struck by the
closing door

Persons can be struck when the door is closed
or collide with the door.
•

The door must be visible from the place of
operation.

Functional description for the door operation

The control allows for the selection of different operating modes:

Dead man OPEN / dead man CLOSE

By pressing the

button continuously (dead man function), the

door operation starts in the OPEN direction until the OPEN door
end position has been reached or the door operation is stopped
by letting go of the button. The door is closed by continuously
pressing the

button (dead man function) until the door end po-

sition has been reached. If you let go of the

button while the

door is closing, the door will stop immediately.

Access by non-instructed persons only with key switch

and in dead-man mode.

Pulse OPEN / dead man CLOSE

By briefly pressing the

button or by external pulse generators,

the  door  starts  moving  in  the  OPEN  direction  until  the  door  end
position  OPEN  has  been  reached  or  the  door  operation  is
stopped  by  pressing  the

button. Pressing the

button again

continues the opening operation. The door is closed by continu-
ously pressing the

button (dead man function) until the door

end position CLOSE has been reached. If you let go of the
button while the door is closing, the door will stop immediately.

Access by non-instructed persons only with key switch

and in dead-man mode.

Pulse OPEN / pulse CLOSE

By briefly pressing the

button or by external pulse generators,

the door starts moving in the OPEN direction until the door end
position OPEN has been reached or the door operation is
stopped by pressing the

button. By briefly pressing the

but-

ton, the door starts moving in the CLOSE direction until the door
end position CLOSE is reached.
This  operating  mode  requires  the  installation  of  a  closing  edge
safety  device  (menu  item  35).  When  the  closing  edge  safety
device is activated while the door is closing, the door will stop and
a direction reversal will take place. Activation of the safety device
has  no  effect  when  the  door  is  opening.  If  there  is  a  defect,  the
door can be closed by the

button.

Pulsed operation

Initial pulse generation:

•

The drive starts and moves the door to the end position
OPEN or CLOSE that is set.

Pulse generation during the process:

•

The door stops

New pulse:

•

The door continues moving in the opposite direction.

NOTICE

Closing option in dead man mode

If a safety device such as the closing edge safety
device, light grid or photoelectric sensor is de-
fective, pulse CLOSE is deactivated. At this
point, the door can only be closed in dead man
mode. As soon as the faults have been elimin-
ated, closing in pulsed operation is possible
again.

AR operation (automatic closing)

By briefly pressing the

button or an external pulse generator,

the  door  starts  moving  in  the  OPEN  direction  until  the  door  end
position  OPEN  has  been  reached  or  the  door  operation  is
stopped  by  pressing  the

button before. When the set open

time set has elapsed, a warning time of 46 seconds starts after
which the door will close automatically.
If the

button is actuated during door end position OPEN or dur-

ing door movement into direction CLOSE, the AR function is can-
celled.
After reversing 20 times during door movement into direction
CLOSE, the AR function is cancelled in the door end posi-
tion OPEN. It is reactivated with a new start command.

AR operation with reduction by photoelectric sensor

Function as described above, however, an interruption of the pho-
toelectric sensor causes the hold-open time to be cancelled and
the warning time starts. The door closes automatically after the
advance warning time has elapsed.

½ door opening

By pressing the

button, the door is opened up to ½ door open-

ing (menu item 32). This function is not available in the dead
man OPEN / dead man CLOSE operating mode and if a light grid
has been installed.

EMERGENCY operation

WARNING

Risk of being crushed or hit by the moving
door in EMERGENCY operation

Persons can be struck when the door is closed
or collide with the door.
•

For EMERGENCY operation the door
needs to be checked and found to be in per-
fect condition.

•

While the "Dead man" operating mode is
active, a clear view to the door from the
place of operation must be ensured.

EMERGENCY  operation  permits  the  operation  of  the  door  with
defective or tripped safety devices.
EMERGENCY operation is activated after 5 seconds of perman-
ent  actuation  of  "OPEN"  or  "CLOSE"  whilst  E06  or  E07  is  dis-
played and is indicated by an F30 message on the display.
The  control  switches  over  to  the  operating  mode  "dead
man OPEN / dead man CLOSE".