background image

6

SYMBOLOGY ON THE MACHINE

Symbol denoting the solution valve.
Indicates the solution valve lever.

Indication of the maximum 
temperature of the solution detergent.  
It is placed near the charging hole of 
the solution tank.

SYMBOLOGY ON THE MANUAL

Symbol denoting the lifting of the 
squeegee.

Symbol denoting the charge level of 
the batteries.

Symbol denoting the lowering of the 
squeegee.

Symbol denoting the brush.
Indicates the switch of the brush 
motor.

Symbol denoting the suction motor.
Indicates the switch of the suction 
motor.

Symbol denoting the crossed bin.
Indicates that at the end of its activity, 
the machine has to be disposed 
conforming to the laws in force.

Symbol denoting the open book.
Indicates that the operator has to 
read the manual before the use of the 
machine.

Symbol that indicates the obligation of 
wearing safety glasses.

Symbol denoting the open book.
For the good functioning of the battery 
charger, read the manual of the 
constructor.

Symbol that indicates the obligation of 
wearing safety gloves.

Warning symbol.
Read carefully the sections marked 
with this symbol, for the security of 
both the operator and the machine.

Symbol that precedes an important
information about the proper use of 
the machine.

Symbol that indicates the obligations 
of disconnecting the system from 
the batteries by disconnecting the 
connector before operating on the 
machine.

Symbol that indicates operations 
that have to be carried out only by 
qualified personnel.

Symbol denoting switching on.  
Indicates the general switch of the 
machine.

Summary of Contents for TS120-S53-U





















Reviews: