background image

g017342

Figure 32

4.

Close the fuel-shutoff valve; refer to

Fuel Shutoff

Valve (page 13)

.

Important:

If you are repairing the machine,

empty the fuel tank.

5.

After performing the maintenance procedure(s),
open the fuel valve and connect the spark-plug
wire to the spark plug.

Replacing the Air Cleaner

Service Interval:

Yearly

1.

Press down on the latch tabs at top of the
air-filter cover (

Figure 33

).

g364771

Figure 33

1.

Latch tabs (air-filter cover)

3.

Air-filter base

2.

Filter element

2.

Remove the cover.

3.

Remove the filter element (

Figure 33

).

4.

Inspect the paper air filter.

A.

If the filter damaged, wet with oil or fuel, and
excessively dirty, replace it.

B.

If the filter is dirty, tap it on a hard surface
several times or blow compressed air less
than 207 kPa (30 psi) through the side of
the filter that faces the engine.

Note:

Do not brush the dirt off the filter;

brushing forces dirt into the fibers.

5.

Clean the air-filter base and cover using a moist
rag.

Do not wipe dirt into the air duct.

6.

Insert the filter into the filter base.

7.

Install the cover.

19

 

Summary of Contents for 02616





























Reviews: