background image

EEA/UK Privacy Notice

Toro’s Use of Your Personal Information

The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly
from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty,
process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer
satisfaction, improve our products or provide you with product information which may be of interest. Toro may share your information with our subsidiaries,
affiliates, dealers or other business partners in connection these activities. We may also disclose personal information when required by law or in
connection with the sale, purchase or merger of a business. We will never sell your personal information to any other company for marketing purposes.

Retention of your Personal Information

Toro will keep your personal information as long as it is relevant for the above purposes and in accordance with legal requirements. For more information
about applicable retention periods please contact legal@toro.com.

Toro’s Commitment to Security

Your personal information may be processed in the US or another country which may have less strict data protection laws than your country of residence.
Whenever we transfer your information outside of your country of residence, we will take legally required steps to ensure that appropriate safeguards are
in place to protect your information and to make sure it is treated securely.

Access and Correction

You may have the right to correct or review your personal data, or object to or restrict the processing of your data. To do so, please contact us by email
at legal@toro.com. If you have concerns about the way in which Toro has handled your information, we encourage you to raise this directly with us.
Please note that European residents have the right to complain to your Data Protection Authority.

374-0282 Rev C

 

Summary of Contents for 02835

































Reviews: