background image

Form No. 3437-895 Rev A

Slope Sensor Kit

Model No. 02945

Model No. 02946

Model No. 02947

Model No. 02949

Model No. 02950

Installation Instructions

Refer to the following table for the appropriate
kit, traction unit, and traction-unit serial number
combination:

Kit Model
Number

Traction Unit Model
Number

Serial Number

02750 (T4240)

405398421 and above

30654 (CT2240)

405623665 and above

31654 (CT2240)

All serial numbers

02945

30657 (LT3340—cab
equipped)

405006390 and above

30657 (LT3340)

405006390 and above

02946

30659 (LT-F3000)

404879018 and above

02947

30659
(LT-F3000—cab
equipped)

404879018 and above

02949

02750 (T4240—cab
equipped)

405398421 and above

02950

31050TE (PLH800)

320000155 and above

Safety

Safety and Instructional
Decals

Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.

decal140-2710

140-2710

1.

1. Warning—read the

Operator’s Manual

; a fast flashing

light and alarm sounding indicates a steep slope; a slow
flashing light indicates a moderate slope; no light indicates
normal operating conditions.

© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3437-895* A

 

Summary of Contents for 02945









Reviews: