2
All Rights Reserved
Printed in the USA
2004 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Contents
Page
Introduction
2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety
3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety and Instruction Decals
3
. . . . . . . . . . . . . . .
Specifications
3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications
3
. . . . . . . . . . . . . . . . . . . .
Optional Accessories
4
. . . . . . . . . . . . . . . . . . . . . .
Assembly
4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loose Parts
4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Tipper Plates and Weights to the Cutting
Units
5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Floatation Kit
6
. . . . . . . . . . . . . . . . .
Installing the Fixed Head Kit
6
. . . . . . . . . . . . . . . .
Securing the Cutting Units to the Lift Arms
6
. . . .
Mounting the #4 and #5 Tipper Brackets
7
. . . . . .
Mount the Roller Bumpers (Floatation Kit Only)
7
Mounting the Hydraulic Motors to the Cutting
Units
8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Reel to Bedknife Contact
9
. . . . . . .
Adjusting the Height-of-Cut for a Floating Cutting
Unit
9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Method for Changing Height-of-Cut after Initial
Setup of a Floating Cutting Unit
11
. . . . . . . . . . . .
Checking/Adjusting the Cutting Unit Attitude
12
. .
Height-of-Cut Adjustment for a Fixed Cutting
Unit
13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Skids and Front Roller
(Fixed Head Kit)
13
. . . . . . . . . . . . . . . . . . . . . . . .
Maintenance
13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lubrication
13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backlapping
14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Servicing the Bedknife/Bedbar
15
. . . . . . . . . . . . . .
Servicing the Reel Assembly
16
. . . . . . . . . . . . . . . .
Removing the Roller
18
. . . . . . . . . . . . . . . . . . . . . .
Installing the Roller
19
. . . . . . . . . . . . . . . . . . . . . . .
The Toro General Commercial Products Warranty
20
. .
Introduction
Read this manual carefully to learn how to operate and
maintain your product properly. The information in this
manual can help you and others avoid injury and product
damage. Although Toro designs and produces safe
products, you are responsible for operating the product
properly and safely.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model and
serial numbers of your product ready. They are located on
the reel sideplate opposite the drive housing.
Write the product model and serial numbers in the space
below:
Model No.
Serial No.
This manual identifies potential hazards and has special
safety messages that help you and others avoid personal
injury and even death. Danger, Warning, and Caution are
signal words used to identify the level of hazard.
However, regardless of the hazard, be extremely careful.
Danger signals an extreme hazard that will cause serious
injury or death if you do not follow the recommended
precautions.
Warning signals a hazard that may cause serious injury or
death if you do not follow the recommended precautions.
Caution signals a hazard that may cause minor or
moderate injury if you do not follow the recommended
precautions.
This manual uses two other words to highlight
information.
Important
calls attention to special
mechanical information and Note: emphasizes general
information worthy of special attention.
