background image

Product Overview

Specifications.

Tractors

These cutting units will mount on the Greensmaster 3300 and 3400 Traction Units.

Height of Cut

Cutting height is adjusted on the front roller by two vertical screws and held by two locking
cap screws

Height Of Cut Range

Standard bench height-of-cut range is 1.6 mm (0.062 inch) to 12.7 mm (0.500 inch). Bench
height-of-cut range with the High Height of Cut Kit installed is 7 mm (0.285 inch) to 25 mm
(1.00 inch). Effective height of cut may vary depending on turf conditions, type of bedknife,
rollers, and attachments installed

Reel Bearings

Two sealed stainless steel, deep groove ball bearings.

Rollers

The rear roller is a 5.1 cm (2 inch) diameter steel full roller

Bedknife

Replaceable single edged, high carbon steel bedknife is fastened to a machined cast iron
bedbar with 13 screws.

Bedknife Adjustment

Dual screw adjustment to the reel; detents corresponding to 0.018 mm (0.0007 inch)
bedknife movement for each indexed position.

Grass Shield

Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in
wet conditions.

Counterweight

A cast iron weight mounted opposite to the drive motor balances the cutting unit.

Net Weight

8 Blade—32 kg (71 lb), 11 Blade—34 kg (74 lb), 14 Blade—35 kg (77 lb)

Attachments/Accessories

A selection of Toro approved attachments and accessories is
available for use with the machine to enhance and expand
its capabilities. Contact your Authorized Service Dealer or
Distributor or go to www.Toro.com for a list of all approved
attachments and accessories.

8

 

Summary of Contents for 04615

















Reviews: