background image

Form No. 3406-976 Rev A

Valve Conversion Kit

Multi Pro

®

1750 Turf Sprayer

Model No. 136-0372

Installation Instructions

The valve conversion kit is a kit that replaces the sprayer control valves and related components for a turf spray application
vehicle.

You may contact Toro directly at www.Toro.com for product safety and operation training materials, accessory information,
help finding a dealer, or to register your product.

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California to

cause cancer, birth defects, or reproductive harm.

Use of this product may cause exposure to chemicals known to the State of California

to cause cancer, birth defects, or other reproductive harm.

Safety

WARNING

Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals,
plants, soils, or other property.

Carefully read and follow the chemical warning labels and material safety data sheets (MSDS) for all
chemicals used and protect yourself according to the chemical manufacturer's recommendations. For
example, use appropriate personal protective equipment (PPE), including face and eye protection,
gloves, or other equipment to guard against personal contact with a chemical.

There may be more than 1 chemical used and information on each chemical should be assessed.

Refuse to operate or work on the sprayer if this information is not available.

Before working on a spray system, ensure that the system has been triple rinsed and neutralized
according to the recommendations of the chemical manufacturer(s) and that all the valves have been
cycled 3 times.

Verify that there is an adequate supply of clean water and soap nearby, and immediately wash off any
chemicals that contact you.

© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3406-976* A

 

Summary of Contents for 136-0372

































































Reviews: