Toro 2003, Operator'S Manual

Engine: 

Briggs & Stratton Daihatsu, diesel, three-

cylinder, 4-cycle, overhead valve, water-cooled, 23 hp @
3600 rpm, 850 cc displacement, governed speed of 3200
rpm.  Mechanical fuel pump.  3.31 l oil capacity.

Cooling System: 

The cooling system is filled with a

50/50 solution of water and permanent ethylene glycol
anti-freeze.

Fuel System: 

Fuel tank capacity 20 liters. Fuel filter

with water separator. Fuel shut-off valve.

Traction Drive

: Eaton model 11 hydrostatic transmission

integrally coupled to a Peerless model 1310 axle. Travel
speed range is 0–13.5Km/h (0–8.5 mph) forward and 4.8
Km/h reverse (0–3 mph).

Controls

: Foot-operated traction pedal. hand-operated

throttle, ignition switch, PTO switch, lift lever, parking
brake and seat adjustment.

Cutting Drive: 

Constant-tension belt drive system with

electric clutch utilizing a poly-V belt from the engine to
the jackshaft and BX section V-belt drive from the
jackshaft to each cutting unit.

Tires and Wheels: 

Two 23 x 8.5-12 front-drive turf tires

with 4-ply construction. Rear tires for the four-wheel
configuration, 16 x 6.5-6 turf tires with 4-ply
construction. Rear tire for the three-wheel configuration,
18 x 6.5-8 with 4-ply construction.

Electrical Features: 

12-volt, 255 cold cranking amps at

180 C, 50-amp reserve capacity at 270 C.  Battery, 16-
amp alternator, seat, traction, PTO and parking brake
interlock switches; electrical leads provided for optional
light and hour meter installations.

Steering: 

Pinion and gear sector with solid control link

to the rear steer assembly, 2.5 turns lock to lock.

Brakes: 

Service braking accomplished through

hydrostatic transmission. Parking brake controls
secondary shaft internal to the axle assembly and is
actuated by a control lever.

Main Frame: 

All-steel welded construction utilizing

tubular and formed sheet metal sections

Seat: 

Standard cushion seat and optional deluxe

suspension seat with arm rest and weight adjustment.
The seat is adjustable fore and aft.  Arm rest kit also
available.

Lift System:

Category “0” A-Frame mounting system

connected to the tractor via parallel linkage. One double-
acting 60 mm bore, 140-mm stroke hydraulic cylinder
receiving oil from hydrostatic transmission charge pump
via the control valve with float position. Maximum
operating pressure is 6895 kPa.  When the traction unit is
equipped with cutting units, all three units are raised and
lowered via the single control lever. The lift system
works with the electric clutch to engage and disengage
the cutting units.

Overall Dimensions and Weight:

Wheel Tread Width

105.3 cm

Width across Front Tires

132 cm

Wheel Base

138.5 cm

Overall Length w/ Cutting Units Installed

229 cm

Overall Height

119 cm

Tractor Weight

50.4 kg

Weight with 5-Blade Fixed Cutting Units

640 kg

Weight with 8-Blade Floating Cutting Units

696 kg

Overall Width w/Fixed-Head Units

195 cm

Overall Width w/Floating Head Units

203 cm

Transport Width w/Fixed Head Units

140 cm

Transport Width w/Floating Head Units

200 cm

Optional Equipment:

Left. 5-Blade Fixed Cutting Unit (2 req.)

Model No. 03434

Right. 5-Blade Fixed Cutting Unit

Model No. 03436

Left 8-Blade Floating Cutting Unit (2 req.) Model No. 03437

Right 8-Blade Floating Cutting Unit 

Model No. 03439

Lift Arm Kit, Fixed Cutting Unit

Model No. 02100

Lift Arm Kit, Floating Cuffing Unit

Model No. 02101

Rear Axle, 4 Wheel

Model No. 02201

Full Roller Kit*

Model No. 03440

Sectional Roller Kit*

Model No. 03445

Wiehle Roller Kit*

Model No. 03450

Skid Kit*

Model No. 03446

Anti-Scalp Roller Kit*

Model No. 03447

Grass Basket Kit, Floating C.U.

Model No. 02302

Grass Basket Kit, Fixed C.U.

Model No. 02304

9

Specifications