background image

Form No. 3388-701 Rev A

20in Recycler

®

/Rear Bagging Lawn Mower

Model No. 20319—Serial No. 315000001 and Up

Operator's Manual

Replacement parts are available from an Authorized Service Dealer or at www.shoptoro.com

Introduction

This rotary-blade, walk-behind lawn mower is intended
to be used by residential homeowners or professional,
hired operators. It is designed primarily for cutting grass
on well-maintained lawns on residential or commercial
properties. It is not designed for cutting brush or for
agricultural uses.

Read this information carefully to learn how to operate and
maintain your product properly and to avoid injury and
product damage. You are responsible for operating the
product properly and safely.

You may contact Toro directly at www.Toro.com for product
and accessory information, help finding a dealer, or to register
your product.

Whenever you need service, genuine Toro parts, or additional
information, contact an Authorized Service Dealer or Toro
Customer Service and have the model and serial numbers of
your product ready.

Figure 1

identifies the location of the

model and serial numbers on the product. Write the numbers
in the space provided.

G020042

1

Figure 1

1.

Model and serial number plate

Model No.

Serial No.

This manual identifies potential hazards and has safety
messages identified by the safety alert symbol (

Figure 2

),

which signals a hazard that may cause serious injury or death
if you do not follow the recommended precautions.

Figure 2

1.

Safety alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical information

and

Note

emphasizes general information worthy of special

attention.

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals

known to the State of California to cause cancer,

birth defects, or reproductive harm.

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

Important:

This engine is not equipped with a spark

arrester muffler. It is a violation of California Public
Resource Code Section 4442 to use or operate the engine
on any forest-covered, brush-covered, or grass-covered
land. Other states or federal areas may have similar laws.

This spark ignition system complies with Canadian ICES-002.

The enclosed

Engine Owner's Manual is supplied for

information regarding the US Environmental Protection
Agency (EPA) and the California Emission Control
Regulation of emission systems, maintenance, and
warranty. Replacements may be ordered through the
engine manufacturer.

For models with stated engine horsepower, the gross
horsepower of the engine was laboratory rated by the engine
manufacturer in accordance with SAE J1940. As configured
to meet safety, emission, and operating requirements, the

© 2014—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3388-701* A

 

Summary of Contents for 20319

















Reviews: