background image

Figure 8

1.

ROPS knob

3.

Roll bar in the upright
position

2.

Pull ROPS knob out and
rotate 90 degrees

4.

Roll bar in the folded
position

4.

To raise the roll bar, raise the roll bar to the operate
position, rotate the knobs so they move partially into
the grooves (Figure 8).

5.

Raise the roll bar to the full upright position while
pushing on the upper roll bar and the pins will snap
into position when the holes align with the pins
(Figure 8). Push on the roll bar and ensure that both
pins are engaged.

Important:

Always use the seat belt with the roll

bar in the fully raised position.

Think Safety First

Please read all safety instructions and symbols in the safety
section. Knowing this information could help you or
bystanders avoid injury.

DANGER

Operating on wet grass or steep slopes can cause
sliding and loss of control.

Wheels dropping over edges can cause rollovers,
which may result in serious injury, death or
drowning.

There is no rollover protection when the roll bar is
down.

Always keep the roll bar in the fully raised and
locked position and use the seat belt.

Read and follow the rollover protection instructions
and warnings.

To avoid loss of control and possibility of rollover:

Do not operate near drop-offs or near water.

Do not operate on slopes greater than 15 degrees.

Reduce speed and use extreme caution on
slopes.

Avoid sudden turns or rapid speed changes.

Figure 9

1.

Safe Zone-use the
Z Master here on slopes
less than 15 degrees or
flat areas.

3.

Water

2.

Danger Zone- use a walk
behind mower and/or a
hand trimmer on slopes
greater than 15 degrees,
near drop-offs and water.

CAUTION

This machine produces sound levels in excess of
85 dBA at the operators ear and can cause hearing
loss through extended periods of exposure.

Wear hearing protection when operating this
machine.

16

Summary of Contents for 74901 Z Master 5000





































































Reviews: