background image

12

m–3457

1

2

Figure 22

1.

Mid Attach-A-Matic

button

2.

Mid Attach-A-Matic

lever

10. Pull the two spring loaded J-pins from the deck lift arms

and twist them slightly so that they stay disengaged
(Fig. 23).

m–3456

1

Figure 23

1.

J-pin

11. If you wish to remove the pulley box, push the latch

release buttons on the front Attach-A-Matic

 (Fig. 24)

and raise the latch levers to open the latches holding the
pulley box. Remove the pulley box.

m–5511

3

1

2

2

Figure 24

1.

Front Attach–A–Matic

button (one on each side)

2.

Front Attach–A–Matic

latches

3.

Pulley box

12. Start the tractor and raise the attachment lift to provide

ample clearance to slide out the mower.

13. Stop the engine and remove the ignition key.

14. Slide the mower out from the right side of the tractor.

Operation

Danger

Without the grass deflector, discharge cover, or
complete grass catcher assembly mounted in place,
you and others are exposed to blade contact and
thrown debris. Contact with the rotating mower
blades and thrown debris will cause injury or
death.

Never remove the grass deflector from the
mower because the grass deflector routes
material down toward the turf. If the grass
deflector is ever damaged, replace it
immediately.

Never put your hands or feet under the mower.

Never try to clear the discharge area or mower
blades unless you move the PTO to Off and
rotate the ignition key to Off. Also remove the
key and pull the wires off of the spark plugs.

Summary of Contents for 78449





















Reviews: