background image

GB–1

Contents

Page

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Safety

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Before Operating

2

. . . . . . . . . . . . . . . . . . . . 

While Operating

2

. . . . . . . . . . . . . . . . . . . . . 

Maintaining Snowthrower

3

. . . . . . . . . . . . . 

Sound Pressure Level

4

. . . . . . . . . . . . . . . . . 

Vibration Level

4

. . . . . . . . . . . . . . . . . . . . . 

Symbol Glossary

4

. . . . . . . . . . . . . . . . . . . . 

Assembly

8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Install Discharge Chute (Fig. 2)

8

. . . . . . . . . 

Install Handle (Fig. 3)

8

. . . . . . . . . . . . . . . . 

Install Control Cable

8

. . . . . . . . . . . . . . . . . 

Before Starting

9

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Mix Gasoline and Oil (Fig. 6)

9

. . . . . . . . . . 

Operation

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Starting/Stopping Engine (Fig. 7)

10

. . . . . . . 

Operating Tips (Fig. 8)

11

. . . . . . . . . . . . . . . . 

Folding Snowthrower (Fig. 9)

12

. . . . . . . . . . 

Maintenance

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Adjusting Control Bar

12

. . . . . . . . . . . . . . . . 

Draining Gasoline

13

. . . . . . . . . . . . . . . . . . . 

Replacing Rotor Blades (Fig. 10-11)

13

. . . . . 

Replacing Scraper (Fig. 12-13)

14

. . . . . . . . . 

Replacing Drive Belt (Fig. 14-16)

14

. . . . . . . 

Replacing Spark Plug (Fig. 17-19)

14

. . . . . . 

Adjusting Carburetor

15

. . . . . . . . . . . . . . . . . 

Storage

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Introduction

Thank you for purchasing a Toro product.

All of us at Toro want you to be completely satisfied
with your new product, so feel free to contact your
local Authorized Service Dealer for help with service,
genuine Toro parts, or other information you may
require.

Whenever you contact your Authorized Service
Dealer or the factory, always know the model and
serial numbers of your product. These numbers will
help the Service Dealer or Service Representative
provide exact information about your specific
product. You will find the model and serial number
decal located in a unique place on the product as
shown in Figure 1.

For your convenience, write the product model and
serial numbers in the space below.

Model No:

Serial No.

Read this manual carefully to learn how to operate
and maintain your product correctly. Reading this
manual will help you and others avoid personal injury
and damage to the product. Although Toro designs,
produces and markets safe, state-of-the-art products,
you are responsible for using the product properly
and safely. You are also responsible for training
persons who you allow to use the product about safe
operation.

The Toro warning system in this manual identifies
potential hazards and has special safety messages that
help you and others avoid personal injury, even death.
DANGER, WARNING and CAUTION are signal
words used to identify the level of hazard. However,
regardless of the hazard, be extremely careful.

DANGER signals an extreme hazard that will cause
serious injury or death if the recommended
precautions are not followed.

WARNING signals a hazard that may cause serious
injury or death if the recommended precautions are
not followed.

CAUTION signals a hazard that may cause minor or
moderate injury if the recommended precautions are
not followed.

Summary of Contents for CCR POWERLITE 38177

























Reviews: