background image

June 2013© 

Toro GM3280 ROPS Cab Operator Manual

 

 

9. Use your turn signals, checking for traffic well in advance of turning

If the tractor  is not 

equipped with turn signals and law requires them, install them prior to operating on or near 

public roads. 

 

 

Safety Decals 

 

1. Keep decals clean. Remove dirt with a wet clean cloth when necessary. 

2. Replace safety decals if destroyed, missing, painted over or unreadable. If any safety decals 

are covered or  obscured when the ROPS  is mounted,  it is recommended that you purchase 

replacement decals from the tractor manufacturer. Mount them in a readable location at, or 

near, their original location before operating the tractor. 

3. New ROPS decals and tractor decals are available from your tractor dealer. 

 

 

ROPS Safety 

 

1. Install the ROPS in accordance with Tektite mounting instructions. Failure to do so may affect 

the ROPS ability to withstand a roll over.  

2. If the ROPS is subjected to alteration, structural damage or involved in an over turn accident, 

the entire structure must be replaced. Failure to do so may result in injury or death in the event 

of a roll over. 

3. If the tractor in not equipped with seat belts, purchase approved seat belts from the tractor 

manufacturer or Tektite prior to operating the tractor. 

4. Always fasten seat belts prior to operating the tractor. 

5. Always operate the tractor from the operator’s seat. 

6. Remove mud, crop residue, chains and tools from steps and operator’s platform. They may 

interfere with pedal operation or entry/exit from the tractor. 

7. Remove all loose chains, tools, and equipment from the operator’s platform. Failure to do so 

may cause injury or death in the event of a roll over. 

8. Do not install the ROPS on a tractor model that the ROPS is not designated for (compatible 

tractor  designations  are  printed on the ROPS  serial number plate).  The ROPS is designed 

specifically for individual models to ensure ROPS requirements will be met. Installing the ROPS 

on a non designated tractor may result in injury or death. 

 

Emergency Exits 

 

The economy ROPS cab has one door.  However, all vinyl panels are fastened with buttons, so 

escape window or rear window  may be used in an  emergency  by pushing out the vinyl  and 

unsnapping the buttons. 

 

The deluxe ROPS cab has two doors.  Either one can be used during an emergency. 

 

 

Summary of Contents for GM3280



















Reviews: