background image

Figure 23

1.

Snow cleanout tool (attached to the handle)

Operation

Note:

Determine the left and right sides of the machine

from the normal operating position.

Freewheeling or Using the
Self-propel Drive

You can operate the snowthrower with the self-propel feature
engaged or disengaged (freewheeling).

To freewheel, slide the wheels inward and insert the axle
pins through the axle holes, but not through the wheel hubs
(Figure 24).

Figure 24

To self-propel, slide the wheels outward and insert the axle
pins through the holes in the wheel hubs and the axle holes
(Figure 25).

Figure 25

Filling the Fuel Tank

Recommended Fuel:

For best results, use only clean, fresh (less than 30 days
old), unleaded gasoline with an octane rating of 87 or
higher ((R+M)/2 rating method).

Ethanol

: Gasoline with up to 10% ethanol (gasohol)

or 15% MTBE (methyl tertiary butyl ether) by volume

is acceptable. Ethanol and MTBE are not the same.
Gasoline with 15% ethanol (E15) by volume is not
approved for use.

Never use gasoline that contains

more than 10% ethanol by volume

, such as E15

(contains 15% ethanol), E20 (contains 20% ethanol), or
E85 (contains up to 85% ethanol ). Using unapproved
gasoline may cause performance problems and/or engine
damage which may not be covered under warranty.

Do not

use gasoline containing methanol.

Do not

store fuel either in the fuel tank or fuel containers

over the winter unless a fuel stabilizer is used.

Do not

add oil to gasoline.

Important:

To reduce starting problems, add fuel

stabilizer to the fuel all season, mixing it with gasoline
less than 30 days old; run the machine dry before storing
it for more than 30 days.
Do not use fuel additives other than a fuel
stabilizer/conditioner. Do not use fuel stabilizers
with an alcohol base such as ethanol, methanol, or
isopropanol.

DANGER

Gasoline is extremely flammable and explosive. A
fire or explosion from gasoline can burn you and
others.

To prevent a static charge from igniting the
gasoline, place the container and/or machine
directly on the ground before filling, not in a
vehicle or on an object.

Fill the tank outdoors when the engine is cold.
Wipe up spills.

Do not handle gasoline when smoking or around
an open flame or sparks.

Store gasoline in an approved fuel container, out
of the reach of children.

Note:

Never use methanol, gasoline containing methanol,

or gasoline containing more than 10% ethanol because the
fuel system could be damaged.

14

 

Summary of Contents for Power Max Heavy Duty 1128 OHXE 38803





































Reviews: