Toro Recycler 20016 Operator'S Manual Download

Page: 6 / 16

Adjusting the Cutting Height

Adjusting the cutting height may bring you into contact with the moving blade, causing serious injury.

•

Stop the engine and wait for all moving parts to stop.

•

Do not put your ﬁngers under the housing when adjusting the cutting height.

If the engine has been running, the mufﬂer will be hot and can severely burn you. Keep away from the hot
mufﬂer.

Adjust the cutting height as desired. Set all four wheels to the same height.

Note:

Only a front cutting height lever is shown.

Figure 11

Adjusting the Handle Height

Squeeze the bottom of the handle halves together and
change the handle holes in which the pins are mounted,
as shown in Figure 12.

Figure 12

1. Pin

3. Use this hole to lower the

handle

2. Use this hole to raise the

handle

Summary of Contents for Recycler 20016

















Search results

Summary of Contents for Recycler 20016

Reviews:

Related manuals for Recycler 20016

Brands by name

Popular brands

Toro Recycler 20016, Operator'S Manual

Search results

Summary of Contents for Recycler 20016

Reviews:

Related manuals for Recycler 20016

Brands by name

Popular brands