Axles, Planetaries
and Brakes
Reelmaster 6500–D/6700–D
Page 6 – 19
Axles, Planetaries and Brakes
Installing Drag Link and Tie Rod Arm
1. Carefully insert bushing into arm.
2. Put arm into position over holder, fitting it to final case
and secure to case with bolts.
3. Check thrust clearance. Proper thrust clearance is 0
to 0.2 mm (0.008in.). If necessary reduce clearance to
specification by shimming. Shim stock for this adjust-
ment is available in the following thicknesses:
Thickness
Shim Part No.
Part No.
TIE ROD ARM
DRAG LINK ARM
Shim set
77-4050
77-4040
0.8 mm (0.03 in.)
76-7820
76-7700
1.0 mm (0.04 in.)
76-7970
76-7760
1.2 mm (0.05 in.)
76-7980
76-7780
1.4 mm (0.055 in.)
76-7990
76-7790
4. After selecting required shim, remove the arm. Apply
multi–purpose lithium base grease to OD part of holder.
Install holder on arm with shim and secure to final case
by tighten reamer bolts to following torque value:
Torque specification
8.5 ~ 9.5 kg–m
(61 ~ 69 ft-lb)
Installing Gear Case Assembly to Axle Housing
1. To check backlash between pinions (14T) –– one on
final drive shaft and one on differential shaft –– tempo-
rarily fit gear case to axle housing and tighten two bolts
diametrically opposite. DO NOT use black reamer bolt
for this temporary assembly.
2. Install a dial indicator to final case, putting gauge
spindle to tooth on pinion (15T pinion on bottom end of
final drive shaft). Take a backlash reading.
Pinion (14T) backlash
0.2 ~ 0.4 mm
(0.008 ~ 0.016 in.)
3. If reading is outside of specified range, remove gear
case and adjust shim between pinion (14T) on differen-
tial shaft and ball bearing. Shim stock for this adjustment
is available in the following thicknesses:
Thickness
Part No.
Shim set
77-4020
0.1 mm (0.004 in.)
76-7520
0.2 mm (0.008 in.)
76-7530
0.4 mm (0.016 in.)
77-7540
Figure 31
Figure 32
Summary of Contents for REELMASTER 6500 D
