Reelmaster 7000
Page 3 -- 7
Kubota Diesel Engine
Removal (Fig. 4)
CAUTION
The muffler and exhaust pipe may be hot. To
avoid possible burns, allow the engine and ex-
haust system to cool before working on the muf-
fler.
1. Park machine on a level surface, lower cutting units,
stop engine, engage parking brake and remove key
from the ignition switch.
2. Raise and support hood.
3. Remove muffler and/or muffler bracket from the en-
gine as necessary using Figure 4 as a guide.
Installation (Fig. 4)
IMPORTANT: If exhaust studs were removed from
engine cylinder head, thoroughly clean threads in
head and apply Loctite #277 (or equivalent) to stud
threads before installing studs into head.
NOTE:
Make sure muffler flange and exhaust manifold
sealing surfaces are free of debris or damage that may
prevent a tight seal.
1. Install
new
exhaust gasket if original gasket is dam-
aged or torn.
IMPORTANT: Failure to follow the suggested muf-
fler fastener sequence may result in premature muf-
fler failure.
2. Install exhaust system components to the engine us-
ing Figure 4 as a guide. Hand tighten all exhaust system
fasteners before fully tightening any fastener.
3. Tailpipe should have equal clearance between frame
and engine after installation.
4. After exhaust system installation is completed, lower
and secure hood.
Kubota
Diesel
Engine
Summary of Contents for Reelmaster 7000
