background image

11

As the bagger fills, extra weight is added to the
back of the machine. If you stop and start
suddenly on hills, you may lose steering control or
the machine may tip.

Do not start or stop suddenly when going uphill

or downhill. Avoid uphill starts.

If you do stop the machine when going uphill,

disengage the PTO. Then back down the hill

using a slow speed.

Do not change speeds or stop on slopes.

Caution

Bagging Long Grass

Excessively long grass is heavy and may not be propelled

completely into the grass bags. If this happens, the

discharge tube and chute may plug. To avoid plugging the

bagging system, mow the grass at a high height of cut, then

lower the mower to your normal cutting height and repeat

the bagging process.

Bagging Wet Grass

Always try to cut grass when it is dry because your lawn

will have a neat appearance. If you must cut wet grass, use

the conventional side discharge feature of the mower.

Several hours later, when the clippings are dry, install the

complete bagger attachment and vacuum up the grass

clippings.

Signs of Plugging

As you are bagging, a small amount of grass clippings

normally blow out the front of the mower. An excessive

amount of clippings blowing out indicates that the bags are

full or the system is plugged.

Maintenance

Note:

 Determine the left and right sides of the machine from the normal operating position.

Recommended Maintenance Schedule

Maintenance Service

Interval

Maintenance Procedure

After each use

Clean the bagger

After the first 10

operating hours, and

monthly thereafter

Inspect the bagger

Storage Service

Clean the bagger

Inspect the bagger

Paint chipped surfaces

Caution

If you leave the key in the ignition switch, someone could accidently start the engine and
seriously injure you or other bystanders.
Remove the key from the ignition and disconnect the wire from the spark plug before you do any
maintenance. Set the wire aside so that it does not accidentally contact the spark plug.

Summary of Contents for TimeCutter Z 79214

















Reviews: