Toshiba 18E2AVG-A, Owner'S Manual

INDOOR UNIT DISPLAY

1

1

2

3

4

5

1

 ECO (White)

2

 Wi-Fi access (White) 

3

 Hi-Power (White)

4

 Timer (White)

5

 Operation Mode

  - Cool (Blue)

  - Heat (Orange)

●

Display brightness can be adjusted, follow procedure on 

%

.

 Require Wireless LAN connecting adapter which available as accessory.

PREPARATION BEFORE USE

2

Preparing Filters

  1. Open the air inlet grille and remove the air filters.

  2. Attach the filters. (see detail in the Installation Manual).

Loading Batteries (when use wireless operation.)

  1. Remove the slide cover.

  2. Insert 2 new batteries (AAA type)

following the (+) and (–) positions.

Clock Setup

  1. Push 

 by tip of the pencil.

    If timer indication is flashing, go to the next step 2.

  2. Press 

 or 

: adjust the time.

3. Press 

  : Set the time.

Remote Control Reset

Push 

 by tip of the pencil or

  1. Remove the batteries.
 

2. Press 

.

3. Insert the batteries.

AIR FLOW DIRECTION

3

1

Press 

 : Move the louver in 

the desired vertical direction.

2

Press 

: Swing the air  

automatically and press again to stop.

3

For horizontal direction, adjust 

manually.

Note

:

      ●  

Do not move the louver manually by others.

      ●  

The louver may automation positioning by some operation mode.

REMOTE CONTROL

4

1
2
3
4
5
6
7
8
9
0
!
@
#
$
%
^
&
*
(
)
-
=
q
w
e

Infrared signal emitter

Memory and Preset button (PRESET)

Start/Stop button

Mode select button (MODE)

Fireplace/8°C button

ECO button
Comfortsleep button(COMFORTSLEEP)

Weekly timer (ON/OFF)

Temp for Weekly timer

On timer button (ON)

Set clock  button  (CLOCK)

Check button (CHECK)

Filter reset button (FILTER)

Temperature button (TEMP)

Swing  louver button  (SWING)

Fan speed  button  (FAN)

Set louver button (FIX)

High power button (Hi POWER)

Power selection/Silent button (P-SEL/SILENT)

Program P1 - P4

Day/Edit button

Setup button (SET)

Off timer button (OFF)

Clear button (CLR)

Reset button (RESET)

1

2

3
4

5
6
7
8
9
0
!
@
#

$
%
^

&
*
(
)
-
=
q

w
e

Note:

●

  The provided Remote Controller is a wireless type, which also can be

    used as a wire. Please see “How to Connect The Remote Controller 

    for Wired Operation”, located in installation instruction, in case of wired

  control is required.

●

In wire operation, remote controller will return to initial condition 

    (PRESET, TIMER and CLOCK will return to initial condition) when user  

    shutdown power supply of Air conditioner.

Note:

●

  While Fireplace operation on heating mode, indoor unit fan always runs  

    and cold air breezing might be occurred.

●

Fireplace and 8°C will operate in Heating mode only.

FIREPLACE1      FIREPLACE 2

Normal 

operation

COOLING / HEATING / FAN ONLY OPERATION

5

1. Press 

 : Select Cool   , Heat 

 or Fan only 

. 

2. Press 

 : Set the desired temperature. Min. 17°C, Max. 30°C

  Fan Only: No temperature indication

3. Press 

 : Select AUTO, LOW  , LOW+  , MED 

,

MED+ 

, HIGH 

 or QUIET 

.

AUTOMATIC OPERATION

6

To automatically select cooling, heating or fan only operation

1. Press 

 : Select Auto A.

  2. Press 

 : Set the desired temperature. Min. 17°C, Max. 30°C.

3. Press 

 : Select AUTO, LOW  , LOW+  , MED 

,

    MED+ 

, HIGH 

 or QUIET 

.

DRY OPERATION

7

For dehumidification, a moderate cooling performance is controlled

automatically.

1. Press 

 : Select Dry 

 .

    2. Press 

 : Set the desired temperature. Min. 17°C, Max. 30°C

Note:

 DRY mode fan speed is set to Auto only.

Hi POWER OPERATION

8

To automatically control room temperature and airflow for faster cooling or 

heating operation (except in DRY and FAN ONLY mode)

  Press 

 : Start and stop the operation.

ECO OPERATION

9

To automatically control room temperature to save energy (except in DRY 

and FAN ONLY mode) 

Press 

 : Start and stop the operation. 

Note:

 Cooling operation; the set temperature will increase automatically 

    1 degree/hour for 2 hours (maximum 2 degrees increase).
    For heating operation the set temperture will decrease.

Fireplace Operation  

Keep indoor unit’s fan blowing continuously during thermo off, to circulate heat 

from other sources over the room. There are three setting parameters: Default 

setting > Fireplace 1 > Fireplace 2

Fireplace 1:

During thermo off period, the indoor unit’s fan will continue to run by the same 

speed, previously selected by end-user.

Fireplace 2:

During thermo off period, the indoor unit’s fan will continue to run at super-low 

speed, programmed from factory.

8°C Heating Operation (8°C)

Heat mode operation for keep room temperature (5-13°C) with less of energy 

usage.

Fireplace and 8°C Heating Operation

FIREPLACE AND 8°C HEATING OPERATION

10

Normal

operation

1122350218-00_S01_182x257_12p_S_p70_210303.indd   4

21/03/03   9:20:59 AM