Toshiba 19LV610U - 18.5" LCD TV Service Manual Download

Page: 8 / 223

Introduction

SLOW ( ) button

Direction buttons ( / / / )

EJECT button

DISPLAY button

Numbered buttons (0-9)

SUBTITLE button

INPUT button

ZOOM button

MENU button

SETUP button

PLAY MODE button

PLAY button

PAUSE button

TOP MENU button

RETURN button

GAME button

TV/DVD button

Direct channel selection
buttons (0-9)

CH RTN button

CLOSED CAPTION button

SKIP ( ) button

REV button

FF button

POWER button

JUMP button

Direct channel selection button ( )

AUDIO SELECT button

MUTE button

EXIT/CANCEL button

SKIP ( )button

STOP button

REPEAT A-B button

PIC SIZE button

ENTER button

SLEEP button

*DVD MENU button

VOL +/– button

SLOW ( ) button
MARKER button

ANGLE button

CH / button

Remote control

The instructions in this manual describe the function on the remote control. See the page in

for details.

*DVD MENU button

Use the DVD MENU button to
display the menu included on
many DVD video discs.
To operate a menu, follow the
instructions in “DVD menu.”

Identification of controls (Continued)

52G0101A.indb 12

1/5/09 3:02:08 PM

Introduction

Replace the compartment
cover.

Install two “R03/AAA” batteries
(supplied), paying attention to
the polarity indicated in the
battery compartment.

Open the battery compartment
cover in the direction of the
arrow.

• Aim the remote control at the remote sensor and press control buttons to operate.
• Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of approx. 5 meters.

Caution:

• Never throw batteries into a re.

Note:

• Be sure to use AAA size batteries.
•

Dispose of batteries in a designated disposal area.

•

Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with
applicable laws and regulations.

•

If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with
new ones.

•

When necessary to replace batteries in the remote control, always replace both batteries with new ones.

Never mix battery types or use new and used batteries in combination.

•

Always remove batteries from remote control if they are dead or if the remote control is not to be used for an extended

period of time. This will prevent battery acid from leaking into the battery compartment.

Inserting batteries

Operation

Approx. 5 meters

52G0101A.indb 13

1/5/09 3:02:08 PM

Connections

75 ohm coaxial cable
(not supplied)

300-75 ohm matching
transformer (not supplied)

UHF 300 ohm
twin-lead wire
(not supplied)

VHF 300 ohm
twin-lead wire
(not supplied)

UHF 300 ohm
twin-lead wire
(not supplied)

VHF 75 ohm
(not supplied)

Antenna

jack

Antenna

jack

Antenna

jack

Combiner
(not supplied)

Antenna

jack

Combiner
(not supplied)

Connect the 75 ohm cable from the combination
VHF/UHF antenna to the antenna jack on the back
of the TV/DVD.

If your combination VHF/UHF antenna has a 300
ohm twin-lead wire, use the 300-75 ohm matching
transformer (not supplied).

Connect the UHF 300 ohm twin-lead wire to the
combiner (not supplied). Connect the VHF 300 ohm
twin-lead wire to the 300-75 ohm matching transformer
(not supplied). Attach the transformer to the combiner,
then attach the combiner to the antenna jack on the
back of the TV/DVD.

Connect the VHF 75 ohm cable and UHF 300 ohm
twin-lead wire to the combiner (not supplied).
Attach the combiner to the antenna jack on the back
of the TV/DVD.

Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system.
If you are using a cable TV service (CABLE), see page

for Cable TV connections.

Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)

Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)

52G0101A P14-29.indd 14

1/5/09 3:02:49 PM

Connections

For basic cable service not requiring a converter/descrambler
box, connect the Cable TV 75 ohm coaxial cable directly to the
Antenna jack on the back of the TV/DVD.

75 ohm
coaxial cable

If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require
the use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available
from the cable company or an electronics supply store). Follow the connections shown below. With the switch in
the “B” position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the “A”
position, tune your TV/DVD to the output of the converter/descrambler box (usually channel 3 or 4) and use the
converter/descrambler box to tune scrambled channels.

Incoming 75 ohm

Cable TV

75 ohm cable to

TV/DVD

Antenna

jack

Antenna

jack

Converter/

descrambler

If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the
incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect
the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections
shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel 3 or 4)
and use the converter/descrambler box to select channels.

For subscribers to basic cable TV service

For subscribers to scrambled cable TV service

For subscribers to unscrambled basic cable TV service with scrambled
premium channels

Splitter

Incoming
75 ohm
Cable TV

A/B switch

75 ohm cable
to TV/DVD

Converter/

descrambler

Antenna

jack

Cable TV connections

This TV/DVD has an extended tuning range and can tune most cable channels without using a Cable TV converter box.
Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for
normal viewing requires the use of a descrambler device which is generally provided by the cable company.

52G0101A P14-29.indd 15

1/5/09 3:02:51 PM