Connections
Connecting to optional equipment (Continued)
Connections
20
Connecting to a PC (Personal Computer)
Before you connect this TV/DVD to your PC, change the adjustment of your PC’s Resolution and Refresh rate (60 Hz).
Connect one end of a (male to male) VGA cable to the video card of the computer and the other end to the VGA connector PC
MONITOR on the rear of the TV/DVD. Attach the connectors firmly with the screws on the plug. In case of a Multimedia computer,
connect the audio cord to the audio output of your Multimedia computer and to the AUDIO connector of the PC AUDIO IN jack of
the TV/DVD. You can also connect the PC with HDMI cable. If you use HDMI cable, you don’t have to connect the audio cord. If
you use HDMI-to-DVI cable, please connect audio cord as same way as VGA cable.
Select “PC” by pressing
INPUT
repeatedly (When you use HDMI cable, Select “HDMI”).
Switch on the computer. The TV/DVD can operate as the computer monitor
Monitor Display modes
MODE
Resolution
Refresh rate
VGA 640x480
60/72/75Hz
VGA
720x400
70Hz
SVGA
800x600
56/60/72/75Hz
XGA
1024x768
60/70/75Hz
WXGA
1280x768
60Hz
WXGA
1280x720
60Hz
WXGA
1360x768
60Hz
To return to normal mode
Press
INPUT
again.
Note:
The on-screen displays will have a different appearance in PC mode than in TV mode.
If there is no video signal from the PC when the unit is in PC mode, “No signal” will appear on the TV/DVD-screen.
•
•
VGA cable (not supplied)
To HDMI IN
To PC IN
Audio cord (not supplied)
Back side
HDMI-to-DVI adapter cable (not supplied)
Connecting an analog audio system (26LV61K only)
This connection allows you to use external speakers with an external audio amplifier to adjust the sound level.
To control the audio:
Turn on the TV and the stereo amplifier.
Turn off the TV’s built-in speakers (see “Turning off the built-in speakers” on page
44
.)
Note:
To hear sound when using an external audio amplifier, the volume of both
the TV and the amplifier must be set to a reasonable listening level.
Back side
Analog audio ampli er
To AUDIO OUT (L/R)
To AUDIO IN
or
To HDMI 1/PC AUDIO IN
Connections
Power source
21
Power source
Note:
Never connect the AC line cord plug to other than the specified voltage (120V 60Hz). Use the attached power cord only.
If the polarized AC cord does not fit into a non-polarized AC outlet, do not attempt to file or cut the blade. It is the user’s
responsibility to have an electrician replace the obsolete outlet.
If you cause a static discharge when touching the unit and the unit fails to function, simply unplug the unit from the AC outlet
and plug it back in. The unit should return to normal operation.
If the AC cord plug is plugged in for the first time, wait for approx. 5 seconds before pressing
POWER
.
•
•
•
•
To use AC power source
Connect the AC cord plug into this TV/DVD’s AC INPUT jack.
Connect the AC cord into an AC outlet.
1.
2.
AC cord (supplied)
AC 120V, 60Hz
Wider Hole
and Blade
AC Outlet
22
Basic setup
Auto Setup
Auto Setup
The Auto Setup function helps to install your TV/DVD easily.
It leads you the Language selection, Air/Cable selection and Automatic
channel search.
IMPORTANT: Make sure that the antenna or cable TV system
connection is made!
POWER
EXIT/CANCEL
/ / /
ENTER
1
To turn on the TV/DVD, press POWER.
POWER indicator on the front of the unit
changes green. It may take approx. 10 seconds
for a picture to appear on screen.
•
2
Auto Setup menu appears on the screen.
Press or to select “Language”, then
press or to select your desired language.
Automatic Search
Auto Setup
Language
Signal Type
Cable
Start
English
: Adjust
: Select
3
Press or to select “Signal Type”, then
press or to select “Air” or “Cable”.
Automatic Search
Auto Setup
Language
Signal Type
Cable
Start
English
: Adjust
: Select
Air
- VHF/UHF channels
Cable - Cable TV channels
4
Press
or
to select “Automatic Search”,
then press
or
ENTER.
Auto Setup
Language
Signal Type
Cable
Start
English
: Select
Automatic Search
ENTER:Set
5
Now the “Automatic Search” starts.
Auto Setup
Language
Signal Type
Cable
Start
Digital Channel Found :
Programming Now
Analog Channel Found : 0
0
English
EXIT : End
Automatic Search
If you press
EXIT/CANCEL
, the Automatic
Search stops and changes to the TV screen.
After the starting setup is completed,
the TV
channel appears on the screen.
•
•
Note:
The Auto Setup function will work only when you
press
POWER
for the first time.
The process of “Automatic Search” may take 15 to
30 minutes to complete, depending on your regional
cable service.
•
•
23
Basic setup
Setting the language
Setting the language
This TV/DVD can display the on screen language in English, French or
Spanish.
Select the language you prefer rst, then proceed with the other menu options.
EXIT/CANCEL
1
To turn on the TV/DVD, press POWER.
POWER indicator on the front of the unit
changes green. It may take approx. 10 seconds
for a picture to appear on screen.
•
2
Press MENU. The TV menu screen will
appear. Press or to select “Setup”, then
press or ENTER.
Picture
Audio
Channel
Lock
Setup
Main Menu
: Select
ENTER:Set
3
Press or to select “Language”.
Video Label
>>
Auto Shut Off
Off
On
Aspect
>>
Reset
Setup
Closed Caption
>>
Language
English
: Adjust
: Select
4
Press or to select the desired language:
English, French (Français) or Spanish
(Español).
5
Press EXIT/CANCEL to return to the normal
screen.
Note:
If no buttons are pressed for more than about 60
seconds, the MENU screen will return to normal
operation automatically.
The TV section has its own menu and the DVD
section also has its own menu
62
.
•
•
MENU
/ / /
ENTER
POWER