Toshiba 24E2AVG-A, Owner'S Manual

DISPLAY LAMP BRIGHTNESS ADJUSTMENT

15

To decrease the display lamp brightness or turn it off.

1.  Press and hold 

)$1

 for 3 seconds until brightness level (

, 

, 

 or 

) is shown on remote control LCD then release the button.

2. Press 

Rise

 or 

Decrease

  to adjust brightness in 4 levels.

Remote control 

LCD

Operation display

Brightness

Lamp illuminates full brightness.

100%

Lamp illuminates 50% brightness.

50%

Lamp illuminates 50% brightness and the 
operation lamp is turned off.

50%

All lamps are turned off.

All turned off

●

 In the examples of 

 and 

, the lamp illuminates for 5 seconds before 

going off.

16

SELF CLEANING OPERATION 
(COOL AND DRY OPERATION ONLY)

17

To protect bad smell caused by the humidity in the indoor unit.

1. If the 

 button is pressed once during “Cool” or “Dry” mode, 

the fan will continue to run for other 30 minutes, then it will turn off 
automatically. This will reduce the moisture in the indoor unit.

2.  To stop the unit immediately, press the 

 more 2 times 

within 30 seconds.

TEMPORARY OPERATION

18

In case of the misplaced or discharged remote control

●

  Pressing the RESET button, the unit can start or 

stop without using the remote control.

●

  Operation mode is set on AUTOMATIC operation, 

preset temperature is 24°C and fan operation is 
automatic speed.

REMOTE CONTROL A-B SELECTION

To separate using of remote control for each indoor unit in case of 2 air 
conditioners are installed nearly.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold 

 button on the Remote Control by the tip of the 

pencil. “00” will be shown on the display. (Picture 

1

)

4. Press 

02'(

 during pushing 

. “B” will show on the display and 

“00” will disappear and the air conditioner will turn OFF. The Remote 
Control B is memorized. (Picture 

2

)

Note:

  1. Repeat above step to reset Remote Control to be A.

2. Remote Control A has not “A” display.

3. Default setting of Remote Control from factory is A.

OPERATION AND PERFORMANCE

20

1.  Three-minute protection feature: To prevent the unit from being activated 

for 3 minutes when suddenly restarted or switched to ON.

2.  Preheating operation: Warm up the unit for 5 minutes before the heating 

operation starts.

3.  Warm air control: When the room temperature reaches the set 

temperature, the fan speed is automatically reduced and the outdoor unit 
will stop.

4.  Automatic defrosting: Fans will stop during defrost operation.
5.  Heating capacity: Heat is absorbed from outdoors and released into 

the room. When the outdoor temperature is too low, use another 
recommended heating apparatus in combination with the air conditioner.

6.  Consideration for accumulated snow: Select the position for outdoor unit 

where it will not be subjected to snow drifts, accumulation of leaves or 
other seasonal debris.

7.  Some minor cracking sound may occur when unit operating. This is normal 

because the cracking sound may be caused by expansion/contraction of 
plastic.

Note:

 Item 2 to 6 for Heating model 

Air conditioner operating conditions

Temp.

Operation

Outdoor Temperature

Room Temperature

Heating

–15°C ~ 24°C

Cooling

–10°C ~ 46°C

21°C ~ 32°C

Dry

–10°C ~ 46°C

17°C ~ 32°C

 Firstly, turn off the circuit breaker.

Indoor Unit and Remote Control

●

  Clean the indoor unit and the remote control with a wet cloth when 

needed.

●

  No benzine, thinner, polishing powder or chemically-treated duster.

Air 

fi

lters

Clean every 2 weeks.

1. Open the air inlet grille.
2. Remove the air 

fi

lters.

3. Vacuum or wash and then dry them.
4. Reinstall the air 

fi

lters and close the air inlet grille.

MAINTENANCE

21

1

2

The unit does not operate.

Cooling or Heating is abnormally low.

●

The power main switch is 
turned off.

●

The circuit breaker is activated 
to cut off the power supply.

●

Stoppage of electric current

●

ON timer is set.

●

The 

fi

 lters are blocked with dust.

●

The temperature has been set 
improperly.

●

The windows or doors are opened.

●

The air inlet or outlet of the outdoor 
unit is blocked.

●

The fan speed is too low.

●

The operation mode is FAN or DRY.

●

POWER SELECTION function is 
set 75% or 50% (

This function is 

depend on remote controller

).

TROUBLESHOOTING (CHECK POINT)

22

Book_01_1120650270_EN.indd   6

11/22/2562 BE   10:35 AM

AUTO RESTART FUNCTION SETTING

This product is designed so that, after a power failure, it can restart 
automatically in the same operating mode as before the power failure.

Information

The product is shipped with Auto Restart function in the ON position.
Turn it OFF if this function is not required.

How to turn OFF the Auto Restart Function

●

 Press and hold the [OPERATION] button on the indoor unit for 3 seconds 

(3 beep sounds but OPERATION lamp does not blink).

How to turn ON the Auto Restart Function

●

 Press and hold the [OPERATION] button on the indoor unit for 3 seconds 

(3 beep sounds and OPERATION lamp blink 5 time/sec for 5 seconds).

Note:

   In case of ON timer or OFF timer are set, AUTO RESTART OPERATION 

does not activate.

 Default setting of AUTO RESTART OPERATION is ON.

19

0 ~ 28°C

●

●