Toshiba 30H83, Service Manual

– 4 –

GENERAL ADJUSTMENTS

WARNING

: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-

TION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF SERVICE MANUAL.

SET-UP  ADJUSTMENT FOR FLAT TUBE

■

The following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :

1. Color Purity
2. Convergence
3. White Balance

Note:

The PURITY/CONVERGENCE MAGNET assembly and rubber wedges need mechanical positioning.
Refer to figure 1.

COLOR PURITY ADUSTMENT

(1)Let the screen face in the installing direction or toward the east (when it is to be moved), bring up the service mode

screen after demagnetizing (front, left, right, and top) with the degaussing coil, receive white signals by pressing the
[TV/VIDEO] button, and then the receiver should be operated for more than 40 minutes.

(2)Perform rough adjustment of the central convergence with the P/C magnet according to the adjustment item.

(3)Receive built-in green signals, loosen set screws on the deflection yoke, remove rubber wedges, and shift the deflection

yoke to toward front.

(4)Move alternately the two 2-pole magnets of the P/C magnets so that the green raster can come to the center of the

screen.

Figure  1.

(5)Receive built-in red and blue signals, check that there is no inclination of the single color raster toward one side, and if

each color tilts to a great extent, make adjustment with the 2-pole magnet so that the 3 colors will come to the center
evenly.

(6)Receive the green raster, shift the deflection yoke from a

foremost position (hitting against the picture tube) to a
backward position horizontally, stop the deflection yoke
at a position where it begins to become a green raster,
and perform accurate marking on the picture tube.

(7)Shift the deflection yoke further backward, and perform

accurate marking at a position where the green raster
begins to being luck.

(8)Fix the deflection yoke at a position 60% forward within

the range marked in items (6) and (7) above.

CONVERGENCE ADJUSTMENTS

* Adjust the convergence magnet to get vest convergence in the the order to (1) ~ (5).

■ 

CENTER CONVERGENCE:

(1)Receive the white crosshatch or dot pattern from the service signal generator.

(2)Use the 2 pieces of main 4-pole magnets of P/C magnets, change the open angle, and align the red and blue vertical

lines on the screen center.

(3)Freeze the open angle of the main 4-pole magnets, turn them simultaneously, and align the horizontal lines.

(4)Take the same steps for items (2) and (3) above and align red/blue with green on the screen center using two 6-pole

magnets.

A

P/C magnet installing position A
• 30"=26.5 mm
• 32"=30.5 mm or 32.5 mm
• 34"=37 mm
• 34"=39 mm

Green Belt

2-pole purity magnet

(27": Magnet is fixed with deflection yoke.)

Main 4-pole convergence magnet (30" : 32")
6-pole convergence magnet (34")

Sub-4-pole convergence magnet (32" : 34")

Sub-4-pole convergence magnet (to be installed on deflection yoke for 30", 32”)

6-pole convergence magnet (30" : 32")
Main 4-pole convergence magnet (34")

Fix the deflection yoke at a position 60% forward from a point
between (6) and (7)

Picture tube

Shift deflection yoke
(6)

(8)

(7) Perform marking of each point on

the tape of picture tube

CRT-D board

P/C Mag

100 60 0%