19
SETTING UP YOUR TV
Engl
ish
k
Press
C
or
c
to view the
DTV
(digital channel) or
ATV
(analogue channel) lists.
l
Use
b
or
B
to move through the list to select a
channel, and then press
OK
to view.
In
ATV
mode, some areas may receive duplicate
stations. There may not be a clear picture or the signal
may be weak, so the station order can be changed
using
ATV Manual Tuning
.
REMEMBER:
Press
TV
at any time to select between
ATV
and
DTV
(DTV Ant TV/Radio/Text, DTV Cable TV/
Radio/Text, DTV Sat TV/Radio/Text if available)
modes.
NOTE:
The time will be set automatically by
transmission but can be advanced or decreased by
using
Local Time Setting
in the
DTV Settings
screen.
m
Select
Next
and press
OK
. The
Satellite Settings
screen will appear. From this window, you can add the
satellites that you wish to tune and configure detailed
settings for each one individually. See “Satellite
settings” on page 20.
Highlight
Done
and press
OK
.
n
If your satellite dish is movable, the following
Positioning
screen will appear.
Press
B
or
b
to highlight
Positioning
, and then press
C
or
c
to find the dish position with the strongest
signal level.
Press
B
or
b
to highlight
Store Position
and press
OK
to store the dish position. Repeat steps 14 and 15
for the next satellite as necessary.
If your satellite dish is not movable, the
Positioning
screen will not appear.
Adjust the dish position manually for the maximum
Signal Level strength.
Highlight
Done
and press
OK
.
o
If the reception testing completes successfully, the
Auto Tuning
startup screen will display.
You can select
Scan Option
from
Free to Air
and
All
.
p
Press
B
or
b
to highlight
Start Scan
, and then press
OK
.
The television will start to search for available
DVB-S
channels. The progress bar will indicate the scan
status.
When the search is complete, the
Auto Tuning
results
screen will display the total number of services found.
q
Use
B
or
b
to move through the list to select a
channel, and then press
OK
to view.
From this menu, you can set the RF input configuration.
a
Press
MENU
/
C
c
to highlight
Setup
icon.
b
Press
B
/
C
c
to highlight
System Setup
icon.
c
Press
OK
to display
System Setup
menu.
d
Press
B
or
b
to select
Ant/Cable/Satellite
and press
C
or
c
to select
Antenna
,
Cable
or
Satellite
.
NOTE:
When you attempt to change the
Ant/Cable/
Satellite
setting, a warning message will appear
followed by PIN entry (if PIN has been set) and a
prompt for
Auto Tuning
.
Satellite
No.
Dish
LNB
ASTRA 19.2˚E
Satellite Settings
1
4
3
2
1
1
Transponder : 1/83 (10743 MHz)
Dish Type : Fixed
Lower LOF (MHz) : 9600
Upper LOF (MHz) : 10600
Switch Type
None
LNB Power
On
Done
Positioning
Signal Level
30%
Go to Stored Position
Store Position
Transponder
1/83 (10743 MHz H)
Positioning
W
E
Go to 0
Satellite : ASTRA 19.2°E
Step Size
1
PLEASE NOTE
The
Quick Setup
menu can also be accessed at any
time from the
Setup/System Setup
menu.
Ant/Cable/Satellite (if available)
Auto Tuning - Satellite
Start Scan
Satellite
Free to Air
ASTRA(19.2°E)
Scan Option
