English
- 15 -
(**)
Limited Models Only
and press
OK
you can select
Network
or set values
such as
Frequency
,
Network ID
and
Search Step
on
the next screen. If you select
No
and press
OK
or the
network search dialogue is not displayed you can set
Start
Frequency
,
Stop
Frequency
and
Search Step
on the next screen. When finished, highlight
Next
and
press
OK
button to continue.
Note:
Searching duration will change depending on the
selected
Search Step
.
Satellite:
If
Satellite
broadcast search option is turned
on, the TV will search for digital satellite broadcasts
after other initial settings are completed. Before
satellite search is performed some settings should
be made.
Depending on the model and the selected country
the next step may be the selection of the installation
type for satellite. You can select to start an operator
installation or a standard installation at this point. If you
want to perform an operator installation set the
Install
Type
as
Operator
and then set the
Satellite Operator
according to your operator preference. Some of the
following steps may differ or be skipped depending on
the selected operator in this step. If you set the
Install
Type
as
Standard
, you can continue with regular
satellite installation and watch satellite channels.
Press
OK
to proceed.
M7 Operator Option (**)
To start an M7 operator installation set the
Install
Type
as
Operator
when prompted and the
Satellite
Operator
as the related M7 operator. Then highlight
Preferred Scan
option and set as
Automatic
channel scan
and press
OK
to start the automatic
search. These options can be preselected depending
on the language and country selections that you
made in the earlier steps of the first time installation
process. You may be asked to select
HD
/
SD
or
country specific channel list according to your M7
operator type. Select one and press
OK
to proceed.
Wait till the scan is finished. Now the list has been
installed.
While performing an M7 operator installation, if you
want to use the satellite installation parameters that
differ from the default settings select the
Preferred
Scan
option as
Manual channel scan
and press the
OK
button to proceed. Antenna
type selection screen
will be displayed next. After selecting the antenna
type and the desired satellite in the following steps
press
OK
in order to change the satellite installation
parameters in the sub-menu.
Fransat Option (**)
To start a
Fransat
installation set the
Install Type
as
Operator
when prompted and than set the
Satellite
Operator
as the related Fransat operator. Then press
the
OK
button to start
Fransat
installation. You can
select to start an automatic or manual installation.
Press
OK
to proceed. Fransat Installation will be
performed and broadcasts will be stored (if available).
If you set the
Install Type
as
Standard
, you can
continue with regular satellite installation and watch
satellite channels.
You can start a Fransat installation at any time later
from the
Settings>Installation>Automatic channel
scan> Satellite
menu.
Antenna
type selection screen may be displayed
next. You can select
Antenna type
as
Direct
,
Single
Satellite Cable
or
DiSEqC switch
by using Left or
Right directional buttons. After selecting your antenna
type press
OK
to see the options to proceed.
Continue
,
Transponder list
and
Configure LNB
options may be
available. You can change the transponder and LNB
settings using the related menu options.
•
Direct:
If you have a single receiver and a direct
satellite dish, select this antenna type. Press
OK
to
continue. Select an available satellite on the next
screen and press
OK
to scan for services.
•
Single Satellite Cable:
If you have multiple receivers
and a single satellite cable system, select this anten-
na type. Press
OK
to continue. Configure settings
by following instructions on the next screen. Press
OK
to scan for services.
•
DiSEqC switch:
If you have multiple satellite dishes
and a DiSEqC switch, select this antenna type. Then
set the DiSEqC version and press
OK
to continue.
You can set up to four satellites (if available) for
version v1.0 and sixteen satellites for version v1.1
on the next screen. Press
OK
button to scan the first
satellite in the list.
Note:
Depending on the model of your TV, DiSEqC version
v1.1 may not be supported and therefore the DiSEqC version
selection step may not be available.
Analogue:
If
Analogue
broadcast search option is
turned on, the TV will search for analogue broadcasts
after other initial settings are completed.
A dialogue screen asking to activate parental control
will be displayed. If you select
Yes
, parental restriction
options will be displayed. Configure as desired and
press
OK
when finished. Select
No
and press
OK
to advance, if you don’t want to activate parental
restrictions.
After the initial settings are completed the TV will start
to search for available broadcasts of the selected
broadcast types.
While the search continues current scan results will be
displayed at the bottom of the screen. You can press
the
Home
,
Back
or
Exit
button to cancel the search.
The channels that have already been found will be
stored in the channel list.
After all the available stations are stored,
Channels
menu will be displayed. You can edit the channel
