background image

English

   - 11 -

Switching On/Off

To Switch the TV On

Connect the power cord to a power source such as a 

wall socket (220-240V AC, 50 Hz). 
To switch on the TV from standby mode either:
• Press the 

Standby

 button, 

Pro/-

 or a 

numeric button on the remote control.

• Press the centre of the joystick on the TV in or push 

it up/down until the TV comes on from standby.

To Switch the TV Off

Press the 

Standby 

button on the remote control or 

press the centre of the joystick on the TV in and hold 

it down for a few seconds, the TV will switch into 

standby mode.

To power down the TV completely, unplug the 

power cord from the mains socket.

Note: When the TV is switched into standby mode, the 

standby LED can blink to indicate that features such as 

Standby Search, Over Air Download or Timer is active. The 

LED can also blink when you switch on the TV from standby 

mode.

First Time Installation

Note: If you are going to perform FRANSAT installation, insert 

the FRANSAT card (optional) into the Conditional Access 

terminal of your TV before switching on your TV.

When turned on for the first time, the language 

selection screen is displayed. Select the desired 

language and press 

OK

.

On the next screen, set your preferences using the 

directional buttons.

Note: Depending on the Country selection you may be asked 

to set and confirm a PIN at this point. The selected PIN cannot 

be 0000. You have to enter it if you are asked to enter a PIN 

for any menu operation later.

About Selecting Broadcast Type

Digital Aerial:

 If 

Digital Aerial

 broadcast search 

option is turned on, the TV will search for digital 

terrestrial broadcasts after other initial settings are 

completed.

Digital Cable:

 If 

Digital Cable

 broadcast search 

option is turned on, the TV will search for digital cable 

broadcasts after other initial settings are completed. 

According to your other preferences a confirmation 

message may be displayed before starting to search. 

Select 

YES

 and press 

OK

 to proceed. To cancel 

operation, select 

NO

 and press 

OK

. You can select 

Network

 or set values such as 

Frequency

Network 

ID

 and 

Search Step

. When finished, press 

OK

 button. 

Note: Searching duration will change depending on the 

selected 

Search Step.

Satellite:

 If 

Satellite

 broadcast search option is 

turned on, the TV will search for digital satellite 

broadcasts after other initial settings are completed. 

Before satellite search is performed some settings 

should be made. Before the satellite search starts, 

a menu will be displayed where you can select to 

start a 

Fransat

 installation. Set the 

Install Type

 as 

Operator

 and than set the 

Satellite Operator

 as the 

related Fransat operator. Then press the 

OK

 button 

to start 

Fransat 

installation. You can select to start an 

automatic or manual installation. 
Press 

OK

 to proceed. Fransat Installation will be 

performed and broadcasts will be stored (if available).
If you set the 

Install Type

 as 

Standard

, you can 

continue with regular satellite installation and watch 

satellite channels. 
You can start a Fransat installation at any time later 

from the 

Installation>Automatic channel scan> 

Satellite

 menu.

There are three types of antenna selection. You can 

select 

Antenna Type

 as 

Direct

Single Satellite 

Cable

 or 

DiSEqC switch

 by using “ ” or “ ” buttons.

• 

Direct: 

If you have a single receiver and a direct 

satellite dish, select this antenna type. Press 

OK

 to 

continue. Select an available satellite on the next 

screen and press 

OK

 to scan for services. 

• 

Single Satellite Cable:

 If you have multiple 

receivers and a single satellite cable system, select 

this antenna type. Press 

OK

 to continue. Configure 

settings by following instructions on the next screen. 

Press 

OK

 to scan for services.

• 

DiSEqC switch:

 If you have multiple satellite dishes 

and a 

DiSEqC switch

, select this antenna type. 

Press 

OK

 to continue. You can set four 

DiSEqC

 

options (if available) on the next screen. Press 

OK

 

button to scan the first satellite in the list.

Analogue: 

If 

Analogue

 broadcast search option is 

turned on, the TV will search for analogue broadcasts 

after other initial settings are completed.
Additionally you can set a broadcast type as your 

favourite one. Priority will be given to the selected 

broadcast type during the search process and the 

channels of it will be listed on the top of the 

Channel 

List

. When finished, press 

OK

 to continue.

A dialogue screen asking to activate parental control 

will be displayed. If you select 

Yes

, parental restriction 

options will be displayed. Configure as desired and 

press 

OK

 when finished. Select 

No

 and press 

OK

 

to advance, if you don’t want to activate parental 

restrictions.
You can activate 

Store Mode

 option at this point. 

This option will configure your TV’s settings for store 

environment and depending on the TV model being 

used, the supported features of it may be displayed 

on the top of the screen as an info banner. This option 

is intended only for store use. It is recommended to 

select 

Home Mode

 for home use. This option will be 

Summary of Contents for 43U5766DG





































Reviews: