Toshiba DP1600 Service Handbook Download

Page: 191 / 239

December 2000 © TOSHIBA TEC

4 - 67

1600/2000/2500 TROUBLESHOOTING

(9) White Spots

Step

Cause/Defect area

Transfer charger unit

Process unit (drum)

Fuser unit

Process unit (Developer)

HVPS (main charger/

developer bias/transfer

charger)

Measures

Clean guide roller.

Ground guide roller shaft properly by apply-

ing conductive oil.

Replace transfer charger unit.

Replace process unit or drum (SRU type).

Clean heat roller. If problem persists, replace

heat roller.

Check to see toner sensor works properly,

and then check toner replenishing procedure.

Adjust output from HVPS, or replace defec-

tive HVPS.

Replace process unit, transfer unit, fuser unit,

or HVPS.

Check items

Foreign matter on guide roller?

Guide roller shaft grounded

improperly?

Transfer charger wire slacked?

Transfer charger case deformed?

Any abnormalities on drum sur-

face?

Toner on heat roller surface?

Scratches on heat roller surface?

Is toner running short?

High-voltage output defective?

If problem persists after measures

are applied, or there is no prob-

lem found in above check, follow

procedure described in right col-

umn.

eeding direction

01/11

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands