Toshiba DP1600 Service Handbook Download

Page: 195 / 239

December 2000 © TOSHIBA TEC

4 - 71

1600/2000/2500 TROUBLESHOOTING

(13) Poor cleaning

Step

Cause/Defect area

Process unit (drum)

Cleaning roller

Heat roller

Measures

Replace process unit or durm (SRU type).

Replace cleaning roller.

Replace heat roller.

Check and fix heater control circuit.

Replace heat roller.

Replace the process unit or the fuser unit.

Check items

Scratches on drum surface?

Cleaning roller damaged or their

life ended?

Bubbles on heat roller (94 mm

pitch on copy)?

Heat roller life ended?

If problem persists after measures

are applied, or there is no prob-

lem found in above check, follow

procedure described in right col-

umn.

eeding direction

01/11

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands