Toshiba DP1600 Service Handbook Download

Page: 197 / 239

December 2000 © TOSHIBA TEC

4 - 73

1600/2000/2500 TROUBLESHOOTING

(15) Background Fogging

Step

Cause/Defect area

Density reproduction

Main charger

Process unit (developer)

Process unit (drum)

HVPS (main charger/

developer bias/

transfer charger

Measures

Adjust density.

Clean main charger wire, replace process unit

or charger wire (SRU type).

Check mechanism.

If problem persists, replace process unit or

drum (SRU type).

Note:

Never touch drum surface.

Adjust output from HVPS, or replace defec-

tive HVPS.

Replace process unit.

Check items

Image density reproduction de-

fect?

Main charger dirty?

Magnetic roller pressure mecha-

nism working normally?

Film formed on drum surface?

High-voltage output defective?

If problem persists after measures

are applied, or there is no prob-

lem found in above check, follow

procedure described in right col-

umn.

eeding direction

01/11

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands