Toshiba DP1600 Service Handbook Download

Page: 221 / 239

1600/2000/2500 UPDATING THE FIRMWARE

5 - 16

December 2000 © TOSHIBA TEC

(6) Press any key on the PC.

Downloading of the main data begins.

Screen display on the PC

LCD display on the copier

05-03-021

Boxes ( ) are displayed one by one

(2 rounds).

Boxes ( ) are erased one by one.

Important:

Some time after downloading begins, the message prompting you to perform the next

operation appears on the PC screen. However, downloading is in progress until the LCD of

the copier blinks as shown below. Do not perform any operation. Performing any operation

during this period may cause the downloading to be discontinued and fail and the copier

may not be recovered unless you use the recovery PWA.

Note:

The downloading time is about 8 minutes.

When downloading ends, all the dots on the copier LCD will blink.

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands