Toshiba DP1600 Service Handbook Download

Page: 224 / 239

December 2000 © TOSHIBA TEC

5 - 19

1600/2000/2500 UPDATING THE FIRMWARE

(11) When downloading ends, the following screen appears.

To perform downloading again:

→

Press the [Enter] key and follow the selected menu again.

To update the main data, proceed to step (4). (on page 5-15)

To update the scanner data, proceed to step (8). (on page 5-17)

To terminate the download program:

→

Press the [C] key while pressing the [Ctrl] key and follow step (12) and subsequent.

(12) Press the [Y] key.

05-03-024

(13) Turn the copier and PC power OFF.

Only when the main data is downloaded, perform the following operation to clear the memory.

(14) While pressing the [*] and [#] keys on the copier, turn the power ON and wait until "Please wait"

message is displyed.

(15) Turn the copier power OFF.

01/06

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands