Toshiba DP1600 Service Handbook Download

Page: 90 / 239

1600/2000/2500 ADJUSTMENT ITEMS

1 - 82

December 2000 © TOSHIBA TEC

1.8.5 CCD unit

(a) Replacing the CCD unit

• Since the lens unit was precisely adjusted at the factory, it must not be readjusted in the field or some of

its components must not be replaced. If necessary, the lens unit should be replaced as a unit.

• When replacing the CCD unit, remove the following 3 screws only (Remove 5 screws only in the TWD

model of DP2500.). Do not loosen or remove other screws.

065-17

065-18

Fig. 1-8-23

065-15

Screw

01/09

DP2500 series TWD model

065-19

Fig. 1-8-22

• Use sufficient care when handling the lens unit. Never hold the precision-adjusted area of the lens unit.

Fig. 1-8-22-1

Screw

Shield plate

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands