24
EN
Auto Tuning (ANALOG)
Programme the tuner to scan only the channels you
can receive in your area.
1
In stop mode, press [SETUP]. Select
“General Setting” using [
U
/
D
],
then press [ENTER/OK].
General Setting Menu will appear.
2
Select “Channel” using [
U
/
D
], then
press [ENTER/OK].
3
Select “ANALOG Channel Setup”
using [
U
/
D
], then press
[ENTER/OK].
4
Select “Auto Tuning” using [
U
/
D
],
then press [ENTER/OK].
The unit will start storing channels available in
your area.
Wait for several minutes to finish channel storing.
• Analogue channels will be stored in channel
901-999 after it is scanned by this unit.
5
Press [SETUP] to exit.
You can select only the channels memorised in
this unit by using
[PROG.
/ ]
.
To cancel auto tuning
Press
[RETURN/BACK]
or
[SETUP]
during scanning.
Note
• The selection will be affected by how you receive TV
channels in your local area.
• If the auto tuning is cancelled during scanning,
some channels not yet tuned may not be received.
• You cannot change the channel when DVD is in any
recording mode (normal recording, One-touch Timer
Recording or timer recording).
Manual Tuning (ANALOG)
You can preset an analogue channel manually and
individually.
1
In stop mode, press [SETUP]. Select
“General Setting” using [
U
/
D
],
then press [ENTER/OK].
2
Select “Channel” using [
U
/
D
], then
press [ENTER/OK].
3
Select “ANALOG Channel Setup”
using [
U
/
D
], then press
[ENTER/OK].
4
Select “Manual Tuning” using
[
U
/
D
], then press [ENTER/OK].
5
Select “Position” using [
U
/
D
], then
press [
P
].
6
Select the position number you wish
to use using [the Number buttons] or
[
U
/
D
], then press [
L
].
• You can select position number 901-999.
• With
[the Number buttons]
, you only need to
enter the last 2 digit numbers.
7
Select “Channel” using [
U
/
D
], then
press [
P
].
8
Press [
U
/
D
] to start scanning.
• The tuner will begin to search up or down
automatically. When a channel is found, the unit
will stop searching and the picture will appear
on the TV screen.
• You can select a desired channel number using
[the Number buttons]
. Refer to the following
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press
[0]
first and then
press
[0]
and
[4]
. Or press
[4]
and then “– – 4”
appears and wait for 2 seconds.)
• If this is the channel you want, press
[
L
]
.
ANALOG
General Setting
Playback
Display
Video
Recording
Clock
Channel
DivX
HDMI
Reset All
Auto Tuning (DVB & ANALOG)
DVB Channel Setup
ANALOG Channel Setup
ANALOG Channel Setup
Auto Tuning
Manual Tuning
Move
ANALOG
Channel Plan
CH Indication
TV Channel
01 – 10
IRA-IRJ, GAP
21 – 69
E21 – E69
74 – 78
X, Y, Z, Z+1, Z+2
80 – 99, 100
S1 – S20, GAP
121 – 141
S21 – S41
Manual Tuning
Channel
Decoder
Skip
Position
1
OFF
ON
901
E7J70BD_EN.book Page 24 Monday, May 7, 2007 3:31 PM
Summary of Contents for DVR D-R17DTKB
Page 85: ...EN 85 E7J70BD_EN book Page 85 Monday May 7 2007 3 31 PM ...
Page 86: ...EN 86 E7J70BD_EN book Page 86 Monday May 7 2007 3 31 PM ...
Page 87: ...EN 87 E7J70BD_EN book Page 87 Monday May 7 2007 3 31 PM ...
Page 88: ...Printed in China 1VMN23632A E7J70BD 78_88_Others_EN fm Page 88 Friday July 13 2007 5 37 PM ...
