Toshiba e-studio 211c Operator'S Manual Download

Page: 151 / 225

8-14

NETWORK SCANNING FUNCTION (USING THE OPTIONAL PRINTER CONTROLLER)

2. PROCEDURE OF SCAN SETTING (Cont.)

Enter the IFax address.

- Enter the IFax address within 80 letters using the alphabet

(touch panel) and numbers (digital keys), then press the
SET key.

- Use the following keys as required.

...Press these keys to move the cursor.

Backspace

...Press this key to delete a letter before the cursor.

Cancel

...Press this key to cancel entry of letters and

go back to the screen in step 1.

C Clear (control panel)...Press this key to delete all letters.

Maximum 10 IFax addresses can be set. Repeat steps 1 to 2
described above for the second and following addresses.

Press the NEW key.

Confirm the entered IFax addresses.

- If 4 or more IFax addresses are set, confirm them using the

key and

key.

- Press the RESET key to clear the setting.

To delete the entered IFax address

- Select the IFax address you want to delete, then press the

DELETE key.

Summary of Contents for e-studio 211c


































































































































































































































Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands

Toshiba e-studio 211c, Operator'S Manual

Search results

Summary of Contents for e-studio 211c

Reviews:

Related manuals for e-studio 211c

Brands by name

Popular brands